aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Documentation/gpio.txt31
-rw-r--r--arch/ppc/8xx_io/commproc.c26
-rw-r--r--arch/ppc/configs/ads8272_defconfig592
-rw-r--r--arch/ppc/platforms/mpc8272ads_setup.c17
-rw-r--r--arch/ppc/platforms/mpc866ads_setup.c17
-rw-r--r--arch/ppc/platforms/mpc885ads_setup.c20
-rw-r--r--drivers/block/cciss.c35
-rw-r--r--drivers/infiniband/hw/cxgb3/iwch_cm.c12
-rw-r--r--drivers/md/bitmap.c4
-rw-r--r--fs/autofs4/root.c6
-rw-r--r--fs/reiserfs/item_ops.c2
-rw-r--r--kernel/params.c4
-rw-r--r--mm/nommu.c1
13 files changed, 595 insertions, 172 deletions
diff --git a/Documentation/gpio.txt b/Documentation/gpio.txt
index 989f1130f4f3..f8528db967fa 100644
--- a/Documentation/gpio.txt
+++ b/Documentation/gpio.txt
@@ -27,7 +27,7 @@ The exact capabilities of GPIOs vary between systems. Common options:
- Output values are writable (high=1, low=0). Some chips also have
options about how that value is driven, so that for example only one
value might be driven ... supporting "wire-OR" and similar schemes
- for the other value.
+ for the other value (notably, "open drain" signaling).
- Input values are likewise readable (1, 0). Some chips support readback
of pins configured as "output", which is very useful in such "wire-OR"
@@ -247,6 +247,35 @@ with gpio_get_value(), for example to initialize or update driver state
when the IRQ is edge-triggered.
+Emulating Open Drain Signals
+----------------------------
+Sometimes shared signals need to use "open drain" signaling, where only the
+low signal level is actually driven. (That term applies to CMOS transistors;
+"open collector" is used for TTL.) A pullup resistor causes the high signal
+level. This is sometimes called a "wire-AND"; or more practically, from the
+negative logic (low=true) perspective this is a "wire-OR".
+
+One common example of an open drain signal is a shared active-low IRQ line.
+Also, bidirectional data bus signals sometimes use open drain signals.
+
+Some GPIO controllers directly support open drain outputs; many don't. When
+you need open drain signaling but your hardware doesn't directly support it,
+there's a common idiom you can use to emulate it with any GPIO pin that can
+be used as either an input or an output:
+
+ LOW: gpio_direction_output(gpio, 0) ... this drives the signal
+ and overrides the pullup.
+
+ HIGH: gpio_direction_input(gpio) ... this turns off the output,
+ so the pullup (or some other device) controls the signal.
+
+If you are "driving" the signal high but gpio_get_value(gpio) reports a low
+value (after the appropriate rise time passes), you know some other component
+is driving the shared signal low. That's not necessarily an error. As one
+common example, that's how I2C clocks are stretched: a slave that needs a
+slower clock delays the rising edge of SCK, and the I2C master adjusts its
+signaling rate accordingly.
+
What do these conventions omit?
===============================
diff --git a/arch/ppc/8xx_io/commproc.c b/arch/ppc/8xx_io/commproc.c
index 3b23bcb35b7a..7a8722beac12 100644
--- a/arch/ppc/8xx_io/commproc.c
+++ b/arch/ppc/8xx_io/commproc.c
@@ -39,6 +39,21 @@
#include <asm/tlbflush.h>
#include <asm/rheap.h>
+#define immr_map(member) \
+({ \
+ u32 offset = offsetof(immap_t, member); \
+ void *addr = ioremap (IMAP_ADDR + offset, \
+ sizeof( ((immap_t*)0)->member)); \
+ addr; \
+})
+
+#define immr_map_size(member, size) \
+({ \
+ u32 offset = offsetof(immap_t, member); \
+ void *addr = ioremap (IMAP_ADDR + offset, size); \
+ addr; \
+})
+
static void m8xx_cpm_dpinit(void);
static uint host_buffer; /* One page of host buffer */
static uint host_end; /* end + 1 */
@@ -364,11 +379,16 @@ static rh_block_t cpm_boot_dpmem_rh_block[16];
static rh_info_t cpm_dpmem_info;
#define CPM_DPMEM_ALIGNMENT 8
+static u8* dpram_vbase;
+static uint dpram_pbase;
void m8xx_cpm_dpinit(void)
{
spin_lock_init(&cpm_dpmem_lock);
+ dpram_vbase = immr_map_size(im_cpm.cp_dpmem, CPM_DATAONLY_BASE + CPM_DATAONLY_SIZE);
+ dpram_pbase = (uint)&((immap_t *)IMAP_ADDR)->im_cpm.cp_dpmem;
+
/* Initialize the info header */
rh_init(&cpm_dpmem_info, CPM_DPMEM_ALIGNMENT,
sizeof(cpm_boot_dpmem_rh_block) /
@@ -442,3 +462,9 @@ void *cpm_dpram_addr(uint offset)
return ((immap_t *)IMAP_ADDR)->im_cpm.cp_dpmem + offset;
}
EXPORT_SYMBOL(cpm_dpram_addr);
+
+uint cpm_dpram_phys(u8* addr)
+{
+ return (dpram_pbase + (uint)(addr - dpram_vbase));
+}
+EXPORT_SYMBOL(cpm_dpram_phys);
diff --git a/arch/ppc/configs/ads8272_defconfig b/arch/ppc/configs/ads8272_defconfig
index d1db7d14780e..6619f9118b00 100644
--- a/arch/ppc/configs/ads8272_defconfig
+++ b/arch/ppc/configs/ads8272_defconfig
@@ -1,42 +1,69 @@
#
# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.21-rc5
+# Wed Apr 4 20:55:16 2007
#
CONFIG_MMU=y
+CONFIG_GENERIC_HARDIRQS=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
-CONFIG_HAVE_DEC_LOCK=y
+CONFIG_ARCH_HAS_ILOG2_U32=y
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
CONFIG_PPC=y
CONFIG_PPC32=y
CONFIG_GENERIC_NVRAM=y
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_ARCH_MAY_HAVE_PC_FDC=y
+CONFIG_GENERIC_BUG=y
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
-CONFIG_CLEAN_COMPILE=y
-CONFIG_STANDALONE=y
CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
#
+CONFIG_LOCALVERSION=""
+CONFIG_LOCALVERSION_AUTO=y
CONFIG_SWAP=y
CONFIG_SYSVIPC=y
+# CONFIG_IPC_NS is not set
+CONFIG_SYSVIPC_SYSCTL=y
# CONFIG_POSIX_MQUEUE is not set
# CONFIG_BSD_PROCESS_ACCT is not set
-CONFIG_SYSCTL=y
+# CONFIG_TASKSTATS is not set
+# CONFIG_UTS_NS is not set
# CONFIG_AUDIT is not set
-CONFIG_LOG_BUF_SHIFT=14
-# CONFIG_HOTPLUG is not set
# CONFIG_IKCONFIG is not set
+CONFIG_SYSFS_DEPRECATED=y
+# CONFIG_RELAY is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SYSCTL=y
CONFIG_EMBEDDED=y
+CONFIG_SYSCTL_SYSCALL=y
# CONFIG_KALLSYMS is not set
+# CONFIG_HOTPLUG is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
# CONFIG_EPOLL is not set
-CONFIG_IOSCHED_NOOP=y
-CONFIG_IOSCHED_AS=y
-CONFIG_IOSCHED_DEADLINE=y
-CONFIG_IOSCHED_CFQ=y
-# CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
+CONFIG_SHMEM=y
+CONFIG_SLAB=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_RT_MUTEXES=y
+# CONFIG_TINY_SHMEM is not set
+CONFIG_BASE_SMALL=0
+# CONFIG_SLOB is not set
#
# Loadable module support
@@ -44,66 +71,124 @@ CONFIG_IOSCHED_CFQ=y
# CONFIG_MODULES is not set
#
+# Block layer
+#
+CONFIG_BLOCK=y
+# CONFIG_LBD is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_LSF is not set
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+# CONFIG_DEFAULT_AS is not set
+# CONFIG_DEFAULT_DEADLINE is not set
+CONFIG_DEFAULT_CFQ=y
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="cfq"
+
+#
# Processor
#
CONFIG_6xx=y
# CONFIG_40x is not set
# CONFIG_44x is not set
-# CONFIG_POWER3 is not set
-# CONFIG_POWER4 is not set
# CONFIG_8xx is not set
+# CONFIG_E200 is not set
+# CONFIG_E500 is not set
+CONFIG_PPC_FPU=y
+# CONFIG_PPC_DCR_NATIVE is not set
+# CONFIG_KEXEC is not set
# CONFIG_CPU_FREQ is not set
+# CONFIG_WANT_EARLY_SERIAL is not set
CONFIG_EMBEDDEDBOOT=y
CONFIG_PPC_STD_MMU=y
#
# Platform options
#
-# CONFIG_PPC_MULTIPLATFORM is not set
+
+#
+# Freescale Ethernet driver platform-specific options
+#
+# CONFIG_PPC_PREP is not set
# CONFIG_APUS is not set
+# CONFIG_KATANA is not set
# CONFIG_WILLOW is not set
-# CONFIG_PCORE is not set
+# CONFIG_CPCI690 is not set
# CONFIG_POWERPMC250 is not set
-# CONFIG_EV64260 is not set
+# CONFIG_CHESTNUT is not set
# CONFIG_SPRUCE is not set
+# CONFIG_HDPU is not set
+# CONFIG_EV64260 is not set
# CONFIG_LOPEC is not set
-# CONFIG_MCPN765 is not set
# CONFIG_MVME5100 is not set
# CONFIG_PPLUS is not set
# CONFIG_PRPMC750 is not set
# CONFIG_PRPMC800 is not set
# CONFIG_SANDPOINT is not set
-# CONFIG_ADIR is not set
-# CONFIG_K2 is not set
+# CONFIG_RADSTONE_PPC7D is not set
# CONFIG_PAL4 is not set
-# CONFIG_GEMINI is not set
# CONFIG_EST8260 is not set
# CONFIG_SBC82xx is not set
# CONFIG_SBS8260 is not set
-# CONFIG_RPX6 is not set
+# CONFIG_RPX8260 is not set
# CONFIG_TQM8260 is not set
CONFIG_ADS8272=y
+# CONFIG_PQ2FADS is not set
+# CONFIG_LITE5200 is not set
+# CONFIG_MPC834x_SYS is not set
+# CONFIG_EV64360 is not set
CONFIG_PQ2ADS=y
CONFIG_8260=y
CONFIG_8272=y
CONFIG_CPM2=y
# CONFIG_PC_KEYBOARD is not set
-CONFIG_SERIAL_CONSOLE=y
# CONFIG_SMP is not set
-# CONFIG_PREEMPT is not set
# CONFIG_HIGHMEM is not set
-CONFIG_KERNEL_ELF=y
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_HZ_300 is not set
+# CONFIG_HZ_1000 is not set
+CONFIG_HZ=250
+CONFIG_PREEMPT_NONE=y
+# CONFIG_PREEMPT_VOLUNTARY is not set
+# CONFIG_PREEMPT is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+# CONFIG_SPARSEMEM_STATIC is not set
+CONFIG_SPLIT_PTLOCK_CPUS=4
+# CONFIG_RESOURCES_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=1
CONFIG_BINFMT_ELF=y
# CONFIG_BINFMT_MISC is not set
# CONFIG_CMDLINE_BOOL is not set
+# CONFIG_PM is not set
+CONFIG_SECCOMP=y
+CONFIG_ISA_DMA_API=y
#
# Bus options
#
+CONFIG_ZONE_DMA=y
+# CONFIG_PPC_I8259 is not set
+CONFIG_PPC_INDIRECT_PCI=y
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
-# CONFIG_PCI_LEGACY_PROC is not set
-# CONFIG_PCI_NAMES is not set
+CONFIG_PCI_8260=y
+
+#
+# PCCARD (PCMCIA/CardBus) support
+#
#
# Advanced setup
@@ -120,12 +205,110 @@ CONFIG_TASK_SIZE=0x80000000
CONFIG_BOOT_LOAD=0x00400000
#
+# Networking
+#
+CONFIG_NET=y
+
+#
+# Networking options
+#
+# CONFIG_NETDEBUG is not set
+CONFIG_PACKET=y
+# CONFIG_PACKET_MMAP is not set
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+# CONFIG_XFRM_USER is not set
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_NET_KEY is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+# CONFIG_IP_ADVANCED_ROUTER is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+# CONFIG_IP_PNP_RARP is not set
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+# CONFIG_IP_MROUTE is not set
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+CONFIG_INET_XFRM_MODE_TRANSPORT=y
+CONFIG_INET_XFRM_MODE_TUNNEL=y
+CONFIG_INET_XFRM_MODE_BEET=y
+CONFIG_INET_DIAG=y
+CONFIG_INET_TCP_DIAG=y
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_INET6_XFRM_TUNNEL is not set
+# CONFIG_INET6_TUNNEL is not set
+# CONFIG_NETWORK_SECMARK is not set
+# CONFIG_NETFILTER is not set
+
+#
+# DCCP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_DCCP is not set
+
+#
+# SCTP Configuration (EXPERIMENTAL)
+#
+# CONFIG_IP_SCTP is not set
+
+#
+# TIPC Configuration (EXPERIMENTAL)
+#
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+# CONFIG_BRIDGE is not set
+# CONFIG_VLAN_8021Q is not set
+# CONFIG_DECNET is not set
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+
+#
+# QoS and/or fair queueing
+#
+# CONFIG_NET_SCHED is not set
+
+#
+# Network testing
+#
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_HAMRADIO is not set
+# CONFIG_IRDA is not set
+# CONFIG_BT is not set
+# CONFIG_IEEE80211 is not set
+
+#
# Device Drivers
#
#
# Generic Driver Options
#
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+# CONFIG_SYS_HYPERVISOR is not set
+
+#
+# Connector - unified userspace <-> kernelspace linker
+#
+# CONFIG_CONNECTOR is not set
#
# Memory Technology Devices (MTD)
@@ -140,6 +323,7 @@ CONFIG_BOOT_LOAD=0x00400000
#
# Plug and Play support
#
+# CONFIG_PNPACPI is not set
#
# Block devices
@@ -149,14 +333,23 @@ CONFIG_BOOT_LOAD=0x00400000
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
+# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_CRYPTOLOOP is not set
# CONFIG_BLK_DEV_NBD is not set
-# CONFIG_BLK_DEV_CARMEL is not set
+# CONFIG_BLK_DEV_SX8 is not set
CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
CONFIG_BLK_DEV_RAM_SIZE=32768
-CONFIG_BLK_DEV_INITRD=y
-# CONFIG_LBD is not set
+CONFIG_BLK_DEV_RAM_BLOCKSIZE=1024
+# CONFIG_CDROM_PKTCDVD is not set
+# CONFIG_ATA_OVER_ETH is not set
+
+#
+# Misc devices
+#
+# CONFIG_SGI_IOC4 is not set
+# CONFIG_TIFM_CORE is not set
#
# ATA/ATAPI/MFM/RLL support
@@ -166,7 +359,14 @@ CONFIG_BLK_DEV_INITRD=y
#
# SCSI device support
#
+# CONFIG_RAID_ATTRS is not set
# CONFIG_SCSI is not set
+# CONFIG_SCSI_NETLINK is not set
+
+#
+# Serial ATA (prod) and Parallel ATA (experimental) drivers
+#
+# CONFIG_ATA is not set
#
# Multi-device support (RAID and LVM)
@@ -176,6 +376,7 @@ CONFIG_BLK_DEV_INITRD=y
#
# Fusion MPT device support
#
+# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
@@ -190,70 +391,12 @@ CONFIG_BLK_DEV_INITRD=y
#
# Macintosh device drivers
#
+# CONFIG_MAC_EMUMOUSEBTN is not set
+# CONFIG_WINDFARM is not set
#
-# Networking support
-#
-CONFIG_NET=y
-
-#
-# Networking options
+# Network device support
#
-CONFIG_PACKET=y
-# CONFIG_PACKET_MMAP is not set
-# CONFIG_NETLINK_DEV is not set
-CONFIG_UNIX=y
-# CONFIG_NET_KEY is not set
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-# CONFIG_IP_ADVANCED_ROUTER is not set
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-# CONFIG_IP_PNP_RARP is not set
-# CONFIG_NET_IPIP is not set
-# CONFIG_NET_IPGRE is not set
-# CONFIG_IP_MROUTE is not set
-# CONFIG_ARPD is not set
-CONFIG_SYN_COOKIES=y
-# CONFIG_INET_AH is not set
-# CONFIG_INET_ESP is not set
-# CONFIG_INET_IPCOMP is not set
-# CONFIG_IPV6 is not set
-# CONFIG_NETFILTER is not set
-
-#
-# SCTP Configuration (EXPERIMENTAL)
-#
-# CONFIG_IP_SCTP is not set
-# CONFIG_ATM is not set
-# CONFIG_BRIDGE is not set
-# CONFIG_VLAN_8021Q is not set
-# CONFIG_DECNET is not set
-# CONFIG_LLC2 is not set
-# CONFIG_IPX is not set
-# CONFIG_ATALK is not set
-# CONFIG_X25 is not set
-# CONFIG_LAPB is not set
-# CONFIG_NET_DIVERT is not set
-# CONFIG_ECONET is not set
-# CONFIG_WAN_ROUTER is not set
-# CONFIG_NET_HW_FLOWCONTROL is not set
-
-#
-# QoS and/or fair queueing
-#
-# CONFIG_NET_SCHED is not set
-
-#
-# Network testing
-#
-# CONFIG_NET_PKTGEN is not set
-# CONFIG_NETPOLL is not set
-# CONFIG_NET_POLL_CONTROLLER is not set
-# CONFIG_HAMRADIO is not set
-# CONFIG_IRDA is not set
-# CONFIG_BT is not set
CONFIG_NETDEVICES=y
# CONFIG_DUMMY is not set
# CONFIG_BONDING is not set
@@ -266,13 +409,31 @@ CONFIG_NETDEVICES=y
# CONFIG_ARCNET is not set
#
+# PHY device support
+#
+CONFIG_PHYLIB=y
+
+#
+# MII PHY device drivers
+#
+# CONFIG_MARVELL_PHY is not set
+CONFIG_DAVICOM_PHY=y
+# CONFIG_QSEMI_PHY is not set
+# CONFIG_LXT_PHY is not set
+# CONFIG_CICADA_PHY is not set
+# CONFIG_VITESSE_PHY is not set
+# CONFIG_SMSC_PHY is not set
+# CONFIG_BROADCOM_PHY is not set
+# CONFIG_FIXED_PHY is not set
+
+#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
-# CONFIG_MII is not set
-# CONFIG_OAKNET is not set
+CONFIG_MII=y
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNGEM is not set
+# CONFIG_CASSINI is not set
# CONFIG_NET_VENDOR_3COM is not set
#
@@ -281,6 +442,9 @@ CONFIG_NET_ETHERNET=y
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_PCI is not set
+CONFIG_FS_ENET=y
+# CONFIG_FS_ENET_HAS_SCC is not set
+CONFIG_FS_ENET_HAS_FCC=y
#
# Ethernet (1000 Mbit)
@@ -292,14 +456,24 @@ CONFIG_NET_ETHERNET=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
+# CONFIG_SIS190 is not set
+# CONFIG_SKGE is not set
+# CONFIG_SKY2 is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
+# CONFIG_QLA3XXX is not set
+# CONFIG_ATL1 is not set
#
# Ethernet (10000 Mbit)
#
+# CONFIG_CHELSIO_T1 is not set
+# CONFIG_CHELSIO_T3 is not set
# CONFIG_IXGB is not set
# CONFIG_S2IO is not set
+# CONFIG_MYRI10GE is not set
+# CONFIG_NETXEN_NIC is not set
#
# Token Ring devices
@@ -321,6 +495,8 @@ CONFIG_NET_ETHERNET=y
# CONFIG_SLIP is not set
# CONFIG_SHAPER is not set
# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
#
# ISDN subsystem
@@ -336,6 +512,7 @@ CONFIG_NET_ETHERNET=y
# Input device support
#
CONFIG_INPUT=y
+# CONFIG_INPUT_FF_MEMLESS is not set
#
# Userland interfaces
@@ -347,14 +524,6 @@ CONFIG_INPUT=y
# CONFIG_INPUT_EVBUG is not set
#
-# Input I/O drivers
-#
-# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
-# CONFIG_SERIO is not set
-# CONFIG_SERIO_I8042 is not set
-
-#
# Input Device Drivers
#
# CONFIG_INPUT_KEYBOARD is not set
@@ -364,6 +533,12 @@ CONFIG_SOUND_GAMEPORT=y
# CONFIG_INPUT_MISC is not set
#
+# Hardware I/O ports
+#
+# CONFIG_SERIO is not set
+# CONFIG_GAMEPORT is not set
+
+#
# Character devices
#
# CONFIG_VT is not set
@@ -377,10 +552,21 @@ CONFIG_SOUND_GAMEPORT=y
#
# Non-8250 serial port support
#
+# CONFIG_SERIAL_UARTLITE is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_SERIAL_CPM=y
+CONFIG_SERIAL_CPM_CONSOLE=y
+CONFIG_SERIAL_CPM_SCC1=y
+# CONFIG_SERIAL_CPM_SCC2 is not set
+# CONFIG_SERIAL_CPM_SCC3 is not set
+CONFIG_SERIAL_CPM_SCC4=y
+# CONFIG_SERIAL_CPM_SMC1 is not set
+# CONFIG_SERIAL_CPM_SMC2 is not set
+# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
-# CONFIG_QIC02_TAPE is not set
#
# IPMI
@@ -391,29 +577,53 @@ CONFIG_LEGACY_PTY_COUNT=256
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
+CONFIG_HW_RANDOM=y
# CONFIG_NVRAM is not set
CONFIG_GEN_RTC=y
# CONFIG_GEN_RTC_X is not set
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
-
-#
-# Ftape, the floppy tape device driver
-#
-# CONFIG_FTAPE is not set
# CONFIG_AGP is not set
# CONFIG_DRM is not set
# CONFIG_RAW_DRIVER is not set
#
+# TPM devices
+#
+# CONFIG_TCG_TPM is not set
+
+#
# I2C support
#
# CONFIG_I2C is not set
#
-# Misc devices
+# SPI support
+#
+# CONFIG_SPI is not set
+# CONFIG_SPI_MASTER is not set
+
#
+# Dallas's 1-wire bus
+#
+# CONFIG_W1 is not set
+
+#
+# Hardware Monitoring support
+#
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_ABITUGURU is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_SM501 is not set
#
# Multimedia devices
@@ -428,7 +638,9 @@ CONFIG_GEN_RTC=y
#
# Graphics support
#
+# CONFIG_BACKLIGHT_LCD_SUPPORT is not set
# CONFIG_FB is not set
+# CONFIG_FB_IBM_GXT4500 is not set
#
# Sound
@@ -436,35 +648,110 @@ CONFIG_GEN_RTC=y
# CONFIG_SOUND is not set
#
+# HID Devices
+#
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+
+#
# USB support
#
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+CONFIG_USB_ARCH_HAS_EHCI=y
# CONFIG_USB is not set
#
+# NOTE: USB_STORAGE enables SCSI, and 'SCSI disk support'
+#
+
+#
# USB Gadget Support
#
# CONFIG_USB_GADGET is not set
#
+# MMC/SD Card support
+#
+# CONFIG_MMC is not set
+
+#
+# LED devices
+#
+# CONFIG_NEW_LEDS is not set
+
+#
+# LED drivers
+#
+
+#
+# LED Triggers
+#
+
+#
+# InfiniBand support
+#
+# CONFIG_INFINIBAND is not set
+
+#
+# EDAC - error detection and reporting (RAS) (EXPERIMENTAL)
+#
+
+#
+# Real Time Clock
+#
+# CONFIG_RTC_CLASS is not set
+
+#
+# DMA Engine support
+#
+# CONFIG_DMA_ENGINE is not set
+
+#
+# DMA Clients
+#
+
+#
+# DMA Devices
+#
+
+#
+# Auxiliary Display support
+#
+
+#
+# Virtualization
+#
+
+#
# File systems
#
CONFIG_EXT2_FS=y
# CONFIG_EXT2_FS_XATTR is not set
+# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
# CONFIG_EXT3_FS_POSIX_ACL is not set
# CONFIG_EXT3_FS_SECURITY is not set
+# CONFIG_EXT4DEV_FS is not set
CONFIG_JBD=y
# CONFIG_JBD_DEBUG is not set
CONFIG_FS_MBCACHE=y
# CONFIG_REISERFS_FS is not set
# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_ROMFS_FS is not set
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
# CONFIG_QUOTA is not set
+CONFIG_DNOTIFY=y
# CONFIG_AUTOFS_FS is not set
# CONFIG_AUTOFS4_FS is not set
+# CONFIG_FUSE_FS is not set
#
# CD-ROM/DVD Filesystems
@@ -475,7 +762,8 @@ CONFIG_FS_MBCACHE=y
#
# DOS/FAT/NT Filesystems
#
-# CONFIG_FAT_FS is not set
+# CONFIG_MSDOS_FS is not set
+# CONFIG_VFAT_FS is not set
# CONFIG_NTFS_FS is not set
#
@@ -483,12 +771,13 @@ CONFIG_FS_MBCACHE=y
#
CONFIG_PROC_FS=y
CONFIG_PROC_KCORE=y
+CONFIG_PROC_SYSCTL=y
CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
-# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
+# CONFIG_TMPFS_POSIX_ACL is not set
# CONFIG_HUGETLB_PAGE is not set
CONFIG_RAMFS=y
+# CONFIG_CONFIGFS_FS is not set
#
# Miscellaneous filesystems
@@ -511,20 +800,26 @@ CONFIG_RAMFS=y
# Network File Systems
#
CONFIG_NFS_FS=y
-# CONFIG_NFS_V3 is not set
-# CONFIG_NFS_V4 is not set
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
-# CONFIG_EXPORTFS is not set
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
-# CONFIG_RPCSEC_GSS_KRB5 is not set
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
# CONFIG_SMB_FS is not set
# CONFIG_CIFS is not set
# CONFIG_NCP_FS is not set
# CONFIG_CODA_FS is not set
# CONFIG_AFS_FS is not set
+# CONFIG_9P_FS is not set
#
# Partition Types
@@ -537,46 +832,99 @@ CONFIG_PARTITION_ADVANCED=y
# CONFIG_MAC_PARTITION is not set
# CONFIG_MSDOS_PARTITION is not set
# CONFIG_LDM_PARTITION is not set
-# CONFIG_NEC98_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
# CONFIG_EFI_PARTITION is not set
#
# Native Language Support
#
# CONFIG_NLS is not set
+
+#
+# Distributed Lock Manager
+#
+# CONFIG_DLM is not set
# CONFIG_SCC_ENET is not set
-CONFIG_FEC_ENET=y
-# CONFIG_USE_MDIO is not set
+# CONFIG_FEC_ENET is not set
#
# CPM2 Options
#
-CONFIG_SCC_CONSOLE=y
-CONFIG_FCC1_ENET=y
-# CONFIG_FCC2_ENET is not set
-# CONFIG_FCC3_ENET is not set
#
# Library routines
#
+# CONFIG_CRC_CCITT is not set
+# CONFIG_CRC16 is not set
# CONFIG_CRC32 is not set
# CONFIG_LIBCRC32C is not set
+CONFIG_PLIST=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+# CONFIG_PROFILING is not set
#
# Kernel hacking
#
+# CONFIG_PRINTK_TIME is not set
+CONFIG_ENABLE_MUST_CHECK=y
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+# CONFIG_DEBUG_FS is not set
+# CONFIG_HEADERS_CHECK is not set
# CONFIG_DEBUG_KERNEL is not set
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_KGDB_CONSOLE is not set
#
# Security options
#
+# CONFIG_KEYS is not set
# CONFIG_SECURITY is not set
#
# Cryptographic options
#
-# CONFIG_CRYPTO is not set
+CONFIG_CRYPTO=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_MANAGER=y
+# CONFIG_CRYPTO_HMAC is not set
+# CONFIG_CRYPTO_XCBC is not set
+# CONFIG_CRYPTO_NULL is not set
+# CONFIG_CRYPTO_MD4 is not set
+CONFIG_CRYPTO_MD5=y
+# CONFIG_CRYPTO_SHA1 is not set
+# CONFIG_CRYPTO_SHA256 is not set
+# CONFIG_CRYPTO_SHA512 is not set
+# CONFIG_CRYPTO_WP512 is not set
+# CONFIG_CRYPTO_TGR192 is not set
+# CONFIG_CRYPTO_GF128MUL is not set
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_PCBC=y
+# CONFIG_CRYPTO_LRW is not set
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_FCRYPT is not set
+# CONFIG_CRYPTO_BLOWFISH is not set
+# CONFIG_CRYPTO_TWOFISH is not set
+# CONFIG_CRYPTO_SERPENT is not set
+# CONFIG_CRYPTO_AES is not set
+# CONFIG_CRYPTO_CAST5 is not set
+# CONFIG_CRYPTO_CAST6 is not set
+# CONFIG_CRYPTO_TEA is not set
+# CONFIG_CRYPTO_ARC4 is not set
+# CONFIG_CRYPTO_KHAZAD is not set
+# CONFIG_CRYPTO_ANUBIS is not set
+# CONFIG_CRYPTO_DEFLATE is not set
+# CONFIG_CRYPTO_MICHAEL_MIC is not set
+# CONFIG_CRYPTO_CRC32C is not set
+# CONFIG_CRYPTO_CAMELLIA is not set
+
+#
+# Hardware crypto devices
+#
diff --git a/arch/ppc/platforms/mpc8272ads_setup.c b/arch/ppc/platforms/mpc8272ads_setup.c
index 0bc06768cf24..47f4b38edb5f 100644
--- a/arch/ppc/platforms/mpc8272ads_setup.c
+++ b/arch/ppc/platforms/mpc8272ads_setup.c
@@ -18,6 +18,7 @@
#include <linux/ioport.h>
#include <linux/fs_enet_pd.h>
#include <linux/platform_device.h>
+#include <linux/phy.h>
#include <asm/io.h>
#include <asm/mpc8260.h>
@@ -30,10 +31,10 @@
#include "pq2ads_pd.h"
-static void init_fcc1_ioports(void);
-static void init_fcc2_ioports(void);
-static void init_scc1_uart_ioports(void);
-static void init_scc4_uart_ioports(void);
+static void init_fcc1_ioports(struct fs_platform_info*);
+static void init_fcc2_ioports(struct fs_platform_info*);
+static void init_scc1_uart_ioports(struct fs_uart_platform_info*);
+static void init_scc4_uart_ioports(struct fs_uart_platform_info*);
static struct fs_uart_platform_info mpc8272_uart_pdata[] = {
[fsid_scc1_uart] = {
@@ -103,7 +104,7 @@ static struct fs_platform_info mpc82xx_enet_pdata[] = {
},
};
-static void init_fcc1_ioports(struct fs_platform_info*)
+static void init_fcc1_ioports(struct fs_platform_info* pdata)
{
struct io_port *io;
u32 tempval;
@@ -144,7 +145,7 @@ static void init_fcc1_ioports(struct fs_platform_info*)
iounmap(immap);
}
-static void init_fcc2_ioports(struct fs_platform_info*)
+static void init_fcc2_ioports(struct fs_platform_info* pdata)
{
cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
u32 *bcsr = ioremap(BCSR_ADDR+12, sizeof(u32));
@@ -229,7 +230,7 @@ static void mpc8272ads_fixup_uart_pdata(struct platform_device *pdev,
}
}
-static void init_scc1_uart_ioports(struct fs_uart_platform_info*)
+static void init_scc1_uart_ioports(struct fs_uart_platform_info* pdata)
{
cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
@@ -246,7 +247,7 @@ static void init_scc1_uart_ioports(struct fs_uart_platform_info*)
iounmap(immap);
}
-static void init_scc4_uart_ioports(struct fs_uart_platform_info*)
+static void init_scc4_uart_ioports(struct fs_uart_platform_info* pdata)
{
cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
diff --git a/arch/ppc/platforms/mpc866ads_setup.c b/arch/ppc/platforms/mpc866ads_setup.c
index 5b05d4bd0df7..7ce5364fdb3b 100644
--- a/arch/ppc/platforms/mpc866ads_setup.c
+++ b/arch/ppc/platforms/mpc866ads_setup.c
@@ -21,6 +21,7 @@
#include <linux/fs_enet_pd.h>
#include <linux/fs_uart_pd.h>
#include <linux/mii.h>
+#include <linux/phy.h>
#include <asm/delay.h>
#include <asm/io.h>
@@ -37,10 +38,10 @@
extern unsigned char __res[];
-static void setup_fec1_ioports(void);
-static void setup_scc1_ioports(void);
-static void setup_smc1_ioports(void);
-static void setup_smc2_ioports(void);
+static void setup_fec1_ioports(struct fs_platform_info*);
+static void setup_scc1_ioports(struct fs_platform_info*);
+static void setup_smc1_ioports(struct fs_uart_platform_info*);
+static void setup_smc2_ioports(struct fs_uart_platform_info*);
static struct fs_mii_fec_platform_info mpc8xx_mdio_fec_pdata;
@@ -137,7 +138,7 @@ void __init board_init(void)
iounmap(bcsr_io);
}
-static void setup_fec1_ioports(struct fs_platform_info*)
+static void setup_fec1_ioports(struct fs_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
@@ -145,7 +146,7 @@ static void setup_fec1_ioports(struct fs_platform_info*)
setbits16(&immap->im_ioport.iop_pddir, 0x1fff);
}
-static void setup_scc1_ioports(struct fs_platform_info*)
+static void setup_scc1_ioports(struct fs_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
unsigned *bcsr_io;
@@ -194,7 +195,7 @@ static void setup_scc1_ioports(struct fs_platform_info*)
}
-static void setup_smc1_ioports(struct fs_uart_platform_info*)
+static void setup_smc1_ioports(struct fs_uart_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
unsigned *bcsr_io;
@@ -216,7 +217,7 @@ static void setup_smc1_ioports(struct fs_uart_platform_info*)
}
-static void setup_smc2_ioports(struct fs_uart_platform_info*)
+static void setup_smc2_ioports(struct fs_uart_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
unsigned *bcsr_io;
diff --git a/arch/ppc/platforms/mpc885ads_setup.c b/arch/ppc/platforms/mpc885ads_setup.c
index f8161f3557f5..87deaefd6c5b 100644
--- a/arch/ppc/platforms/mpc885ads_setup.c
+++ b/arch/ppc/platforms/mpc885ads_setup.c
@@ -35,13 +35,13 @@
#include <asm/ppc_sys.h>
extern unsigned char __res[];
-static void setup_smc1_ioports(void);
-static void setup_smc2_ioports(void);
+static void setup_smc1_ioports(struct fs_uart_platform_info*);
+static void setup_smc2_ioports(struct fs_uart_platform_info*);
static struct fs_mii_fec_platform_info mpc8xx_mdio_fec_pdata;
-static void setup_fec1_ioports(void);
-static void setup_fec2_ioports(void);
-static void setup_scc3_ioports(void);
+static void setup_fec1_ioports(struct fs_platform_info*);
+static void setup_fec2_ioports(struct fs_platform_info*);
+static void setup_scc3_ioports(struct fs_platform_info*);
static struct fs_uart_platform_info mpc885_uart_pdata[] = {
[fsid_smc1_uart] = {
@@ -161,7 +161,7 @@ void __init board_init(void)
#endif
}
-static void setup_fec1_ioports(struct fs_platform_info*)
+static void setup_fec1_ioports(struct fs_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
@@ -181,7 +181,7 @@ static void setup_fec1_ioports(struct fs_platform_info*)
clrbits32(&immap->im_cpm.cp_cptr, 0x00000100);
}
-static void setup_fec2_ioports(struct fs_platform_info*)
+static void setup_fec2_ioports(struct fs_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
@@ -193,7 +193,7 @@ static void setup_fec2_ioports(struct fs_platform_info*)
clrbits32(&immap->im_cpm.cp_cptr, 0x00000080);
}
-static void setup_scc3_ioports(struct fs_platform_info*)
+static void setup_scc3_ioports(struct fs_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
unsigned *bcsr_io;
@@ -315,7 +315,7 @@ static void __init mpc885ads_fixup_scc_enet_pdata(struct platform_device *pdev,
mpc885ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
}
-static void setup_smc1_ioports(struct fs_uart_platform_info*)
+static void setup_smc1_ioports(struct fs_uart_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
unsigned *bcsr_io;
@@ -335,7 +335,7 @@ static void setup_smc1_ioports(struct fs_uart_platform_info*)
clrbits16(&immap->im_cpm.cp_pbodr, iobits);
}
-static void setup_smc2_ioports(struct fs_uart_platform_info*)
+static void setup_smc2_ioports(struct fs_uart_platform_info* pdata)
{
immap_t *immap = (immap_t *) IMAP_ADDR;
unsigned *bcsr_io;
diff --git a/drivers/block/cciss.c b/drivers/block/cciss.c
index 14d780666c0a..65a725cd3422 100644
--- a/drivers/block/cciss.c
+++ b/drivers/block/cciss.c
@@ -3423,6 +3423,25 @@ static void cciss_remove_one(struct pci_dev *pdev)
"already be removed \n");
return;
}
+
+ remove_proc_entry(hba[i]->devname, proc_cciss);
+ unregister_blkdev(hba[i]->major, hba[i]->devname);
+
+ /* remove it from the disk list */
+ for (j = 0; j < CISS_MAX_LUN; j++) {
+ struct gendisk *disk = hba[i]->gendisk[j];
+ if (disk) {
+ request_queue_t *q = disk->queue;
+
+ if (disk->flags & GENHD_FL_UP)
+ del_gendisk(disk);
+ if (q)
+ blk_cleanup_queue(q);
+ }
+ }
+
+ cciss_unregister_scsi(i); /* unhook from SCSI subsystem */
+
/* Turn board interrupts off and send the flush cache command */
/* sendcmd will turn off interrupt, and send the flush...
* To write all data in the battery backed cache to disks */
@@ -3444,22 +3463,6 @@ static void cciss_remove_one(struct pci_dev *pdev)
#endif /* CONFIG_PCI_MSI */
iounmap(hba[i]->vaddr);
- cciss_unregister_scsi(i); /* unhook from SCSI subsystem */
- unregister_blkdev(hba[i]->major, hba[i]->devname);
- remove_proc_entry(hba[i]->devname, proc_cciss);
-
- /* remove it from the disk list */
- for (j = 0; j < CISS_MAX_LUN; j++) {
- struct gendisk *disk = hba[i]->gendisk[j];
- if (disk) {
- request_queue_t *q = disk->queue;
-
- if (disk->flags & GENHD_FL_UP)
- del_gendisk(disk);
- if (q)
- blk_cleanup_queue(q);
- }
- }
pci_free_consistent(hba[i]->pdev, hba[i]->nr_cmds * sizeof(CommandList_struct),
hba[i]->cmd_pool, hba[i]->cmd_pool_dhandle);
diff --git a/drivers/infiniband/hw/cxgb3/iwch_cm.c b/drivers/infiniband/hw/cxgb3/iwch_cm.c
index d0ed1d35ca3e..2d2de9b8b729 100644
--- a/drivers/infiniband/hw/cxgb3/iwch_cm.c
+++ b/drivers/infiniband/hw/cxgb3/iwch_cm.c
@@ -2026,6 +2026,17 @@ static int sched(struct t3cdev *tdev, struct sk_buff *skb, void *ctx)
return 0;
}
+static int set_tcb_rpl(struct t3cdev *tdev, struct sk_buff *skb, void *ctx)
+{
+ struct cpl_set_tcb_rpl *rpl = cplhdr(skb);
+
+ if (rpl->status != CPL_ERR_NONE) {
+ printk(KERN_ERR MOD "Unexpected SET_TCB_RPL status %u "
+ "for tid %u\n", rpl->status, GET_TID(rpl));
+ }
+ return CPL_RET_BUF_DONE;
+}
+
int __init iwch_cm_init(void)
{
skb_queue_head_init(&rxq);
@@ -2053,6 +2064,7 @@ int __init iwch_cm_init(void)
t3c_handlers[CPL_ABORT_REQ_RSS] = sched;
t3c_handlers[CPL_RDMA_TERMINATE] = sched;
t3c_handlers[CPL_RDMA_EC_STATUS] = sched;
+ t3c_handlers[CPL_SET_TCB_RPL] = set_tcb_rpl;
/*
* These are the real handlers that are called from a
diff --git a/drivers/md/bitmap.c b/drivers/md/bitmap.c
index 5554adaa58f9..e61e0efe9ec7 100644
--- a/drivers/md/bitmap.c
+++ b/drivers/md/bitmap.c
@@ -863,9 +863,7 @@ static int bitmap_init_from_disk(struct bitmap *bitmap, sector_t start)
/* We need 4 bits per page, rounded up to a multiple of sizeof(unsigned long) */
bitmap->filemap_attr = kzalloc(
- (((num_pages*4/8)+sizeof(unsigned long)-1)
- /sizeof(unsigned long))
- *sizeof(unsigned long),
+ roundup( DIV_ROUND_UP(num_pages*4, 8), sizeof(unsigned long)),
GFP_KERNEL);
if (!bitmap->filemap_attr)
goto out;
diff --git a/fs/autofs4/root.c b/fs/autofs4/root.c
index b4631046867e..d0e9b3a3905d 100644
--- a/fs/autofs4/root.c
+++ b/fs/autofs4/root.c
@@ -470,9 +470,6 @@ void autofs4_dentry_release(struct dentry *de)
if (inf) {
struct autofs_sb_info *sbi = autofs4_sbi(de->d_sb);
- inf->dentry = NULL;
- inf->inode = NULL;
-
if (sbi) {
spin_lock(&sbi->rehash_lock);
if (!list_empty(&inf->rehash))
@@ -480,6 +477,9 @@ void autofs4_dentry_release(struct dentry *de)
spin_unlock(&sbi->rehash_lock);
}
+ inf->dentry = NULL;
+ inf->inode = NULL;
+
autofs4_free_ino(inf);
}
}
diff --git a/fs/reiserfs/item_ops.c b/fs/reiserfs/item_ops.c
index b9b423b22a8b..9475557ab499 100644
--- a/fs/reiserfs/item_ops.c
+++ b/fs/reiserfs/item_ops.c
@@ -23,7 +23,7 @@ static void sd_decrement_key(struct cpu_key *key)
{
key->on_disk_key.k_objectid--;
set_cpu_key_k_type(key, TYPE_ANY);
- set_cpu_key_k_offset(key, (loff_t) (-1));
+ set_cpu_key_k_offset(key, (loff_t)(~0ULL >> 1));
}
static int sd_is_left_mergeable(struct reiserfs_key *key, unsigned long bsize)
diff --git a/kernel/params.c b/kernel/params.c
index e265b13195b1..1fc4ac746cd8 100644
--- a/kernel/params.c
+++ b/kernel/params.c
@@ -356,6 +356,10 @@ int param_set_copystring(const char *val, struct kernel_param *kp)
{
struct kparam_string *kps = kp->arg;
+ if (!val) {
+ printk(KERN_ERR "%s: missing param set value\n", kp->name);
+ return -EINVAL;
+ }
if (strlen(val)+1 > kps->maxlen) {
printk(KERN_ERR "%s: string doesn't fit in %u chars.\n",
kp->name, kps->maxlen-1);
diff --git a/mm/nommu.c b/mm/nommu.c
index cbbc13774819..1f60194d9b9b 100644
--- a/mm/nommu.c
+++ b/mm/nommu.c
@@ -45,6 +45,7 @@ int heap_stack_gap = 0;
EXPORT_SYMBOL(mem_map);
EXPORT_SYMBOL(__vm_enough_memory);
+EXPORT_SYMBOL(num_physpages);
/* list of shareable VMAs */
struct rb_root nommu_vma_tree = RB_ROOT;