aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2013-02-15Merge branches 'arm-multi_pmu_v2', 'cpufreq-fixes-v3', ↵big-LITTLE-MP-master-v15Viresh Kumar
'hw-bkp-v7.1-debug-v2', 'task-placement-v2', 'task-placement-v2-sysfs', 'misc-patches' and 'config-fragments' into big-LITTLE-MP-master-v15 Updates: ------- - Rebased over 3.8-rc7 - Stats: Total distinct patches: 37 - Dropped Patches: Two patches from cpufreq-fixes-v2 (3): causing some failures. - New Patches: One new patch into task-placement-v2 branch from Sudeep Commands used for merge: ----------------------- $ git checkout -b big-LITTLE-MP-master-v15 v3.8-rc7 $ git merge arm-multi_pmu_v2 cpufreq-fixes-v3 hw-bkp-v7.1-debug-v2 task-placement-v2 task-placement-v2-sysfs misc-patches config-fragments
2013-02-15sched: fix arch_get_fast_and_slow_cpus to get logical cpumask correctlySudeep KarkadaNagesha
The patch "sched: Use device-tree to provide fast/slow CPU list for HMP" depends on the ordering of CPU's in the device tree. It breaks to determine the logical mask correctly if the logical mask of the CPUs differ from physical ordering in the device tree. This patch fix the logic by depending on the mpidr in the device tree and mapping that mpidr to the logical cpu. Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com> Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
2013-02-11sched: Basic global balancing support for HMPMorten Rasmussen
This patch introduces an extra-check at task up-migration to prevent overloading the cpus in the faster hmp_domain while the slower hmp_domain is not fully utilized. The patch also introduces a periodic balance check that can down-migrate tasks if the faster domain is oversubscribed and the slower is under-utilized. Signed-off-by: Morten Rasmussen <morten.rasmussen@arm.com>
2013-02-11ARM: Fix build breakage when big.LITTLE.conf is not used.Chris Redpath
Change-Id: I8641f5e930c65b5672130bd4a18d9868bb3ca594 Signed-off-by: Chris Redpath <chris.redpath@arm.com> Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
2013-02-11ARM: Experimental Frequency-Invariant Load Scaling PatchChris Redpath
Evaluation Patch to investigate using load as a representation of the amount of POTENTIAL cpu compute capacity used rather than a representation of the CURRENT cpu compute capacity. If CPUFreq is enabled, scales load in accordance with frequency. Powersave/performance CPUFreq governors are detected and scaling is disabled while these governors are in use. This is because when a single-frequency governor is in use, potential CPU capacity is static. So long as the governors and CPUFreq subsystem correctly report the frequencies available, the scaling should self tune. Adds an additional file to sysfs to allow this feature to be disabled for experimentation. /sys/kernel/hmp/frequency_invariant_load_scale write 0 to disable, 1 to enable. Signed-off-by: Chris Redpath <chris.redpath@arm.com>
2013-02-11ARM: Change load tracking scale using sysfsOlivier Cozette
These functions allow to change the load average period used in the task load average computation through /sys/kernel/hmp/load_avg_period_ms. This period is the time in ms to go from 0 to 0.5 load average while running or the time from 1 to 0.5 while sleeping. The default one used is 32 and gives the same load_avg_ratio computation than without this patch. These functions also allow to change the up and down threshold of HMP using /sys/kernel/hmp/{up,down}_threshold. Both must be between 0 and 1024. The thresholds are divided by 1024 before being compared to the load_avg_ratio. If /sys/kernel/hmp/load_avg_period_ms is 128 and /sys/kernel/hmp/up_threshold is 512, a task will be migrated to a bigger cluster after running for 128ms. Because after load_avg_period_ms the load average is 0.5 and real up_threshold us 512 / 1024 = 0.5. Signed-off-by: Olivier Cozette <olivier.cozette@arm.com> Signed-off-by: Chris Redpath <chris.redpath@arm.com>
2013-02-11cpufreq: Don't use cpu removed during cpufreq_driver_unregisterViresh Kumar
This is how the core works: cpufreq_driver_unregister() - subsys_interface_unregister() - for_each_cpu() call cpufreq_remove_dev(), i.e. 0,1,2,3,4 when we unregister. cpufreq_remove_dev(): - Remove policy node - Call cpufreq_add_dev() for next cpu, sharing mask with removed cpu. i.e. When cpu 0 is removed, we call it for cpu 1. And when called for cpu 2, we call it for cpu 3. - cpufreq_add_dev() would call cpufreq_driver->init() - init would return mask as AND of 2, 3 and 4 for cluster A7. - cpufreq core would do online_cpu && policy->cpus Here is the BUG(). Because cpu hasn't died but we have just unregistered the cpufreq driver, online cpu would still have cpu 2 in it. And so thing go bad again. Solution: Keep cpumask of cpus that are registered with cpufreq core and clear cpus when we get a call from subsys_interface_unregister() via cpufreq_remove_dev(). Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2013-02-11cpufreq: Notify governors when cpus are hot-[un]pluggedViresh Kumar
Because cpufreq core and governors worry only about the online cpus, if a cpu is hot [un]plugged, we must notify governors about it, otherwise be ready to expect something unexpected. We already have notifiers in the form of CPUFREQ_GOV_START/CPUFREQ_GOV_STOP, we just need to call them now. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2013-02-11cpufreq: Manage only online cpusViresh Kumar
cpufreq core doesn't manage offline cpus and if driver->init() has returned mask including offline cpus, it may result in unwanted behavior by cpufreq core or governors. We need to get only online cpus in this mask. There are two places to fix this mask, cpufreq core and cpufreq driver. It makes sense to do this at common place and hence is done in core. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2013-02-11linaro/configs: big-LITTLE-MP: Enable the new tunable sysfs interface by ↵Liviu Dudau
default. Enable the new tunable sysfs interface for HMP scaling invariants. Signed-of-by: Liviu Dudau <Liviu.Dudau@arm.com>
2013-02-11linaro/configs: Enable HMP priority filter by defaultMorten Rasmussen
This updates linaro config fragments to enable the HMP priority filter by default. Signed-off-by: Morten Rasmussen <morten.rasmussen@arm.com>
2013-02-11config-frag/big-LITTLE: Use device-tree to provide fast/slow CPU list for HMPViresh Kumar
Currently there are two ways of passing list of fast-slow CPU's to kernel. One via configs and other via DT. Code tries to get them via configs first an then try for DT. To make it configurable via DT by default, make config strings empty. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reported-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
2013-02-11linaro/configs: Update big LITTLE MP fragment for task placement workViresh Kumar
CONFIG_HMP_FAST_CPU_MASK and CONFIG_HMP_SLOW_CPU_MASK must be set correctly by user platform. For now they are marked 0-1 and 2-3. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2013-02-11configs: Add config fragments for big LITTLE MPViresh Kumar
This patch adds config fragments used to enable most of the features used by big LITTLE MP. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2013-02-11genirq: Add default affinity mask command line optionThomas Gleixner
If we isolate CPUs, then we don't want random device interrupts on them. Even w/o the user space irq balancer enabled we can end up with irqs on non boot cpus. Allow to restrict the default irq affinity mask. Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2013-02-11sched: Only down migrate low priority tasks if allowed by affinity maskMorten Rasmussen
Adds an extra check intersection of the task affinity mask and the slower hmp_domain cpumask before down migrating low priority tasks. Signed-off-by: Morten Rasmussen <morten.rasmussen@arm.com>
2013-02-11ARM: sched: Avoid empty 'slow' HMP domainJon Medhurst
On homogeneous (non-heterogeneous) systems all CPUs will be declared 'fast' and the slow cpu list will be empty. In this situation we need to avoid adding an empty slow HMP domain otherwise the scheduler code will blow up when it attempts to move a task to the slow domain. Signed-off-by: Jon Medhurst <tixy@linaro.org>
2013-02-11sched: Enable HMP priority filter by defaultMorten Rasmussen
This updates the ARM Kconfig to enable the HMP priority filter by default. Signed-off-by: Morten Rasmussen <morten.rasmussen@arm.com>
2013-02-11sched: SCHED_HMP multi-domain task migration controlMorten Rasmussen
We need a way to prevent tasks that are migrating up and down the hmp_domains from migrating straight on through before the load has adapted to the new compute capacity of the CPU on the new hmp_domain. This patch adds a next up/down migration delay that prevents the task from doing another migration in the same direction until the delay has expired. Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11sched: Add HMP task migration ftrace eventMorten Rasmussen
Adds ftrace event for tracing task migrations using HMP optimized scheduling. Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11sched: Add ftrace events for entity load-trackingMorten Rasmussen
Adds ftrace events for key variables related to the entity load-tracking to help debugging scheduler behaviour. Allows tracing of load contribution and runqueue residency ratio for both entities and runqueues as well as entity CPU usage ratio. Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11ARM: sched: Setup SCHED_HMP domainsMorten Rasmussen
SCHED_HMP requires the different cpu types to be represented by an ordered list of hmp_domains. Each hmp_domain represents all cpus of a particular type using a cpumask. The list is platform specific and therefore must be generated by platform code by implementing arch_get_hmp_domains(). Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11ARM: sched: Use device-tree to provide fast/slow CPU list for HMPMorten Rasmussen
We can't rely on Kconfig options to set the fast and slow CPU lists for HMP scheduling if we want a single kernel binary to support multiple devices with different CPU topology. E.g. TC2 (ARM's Test-Chip-2 big.LITTLE system), Fast Models, or even non big.LITTLE devices. This patch adds the function arch_get_fast_and_slow_cpus() to generate the lists at run-time by parsing the CPU nodes in device-tree; it assumes slow cores are A7s and everything else is fast. The function still supports the old Kconfig options as this is useful for testing the HMP scheduler on devices without big.LITTLE. This patch is reuse of a patch by Jon Medhurst <tixy@linaro.org> with a few bits left out. Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11ARM: Add HMP scheduling support for ARM architectureMorten Rasmussen
Adds Kconfig entries to enable HMP scheduling on ARM platforms. Currently, it disables CPU level sched_domain load-balacing in order to simplify things. This needs fixing in a later revision. HMP scheduling will do the load-balancing at this level instead. Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11sched: Introduce priority-based task migration filterMorten Rasmussen
Introduces a priority threshold which prevents low priority task from migrating to faster hmp_domains (cpus). This is useful for user-space software which assigns lower task priority to background task. Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11sched: Forced task migration on heterogeneous systemsMorten Rasmussen
This patch introduces forced task migration for moving suitable currently running tasks between hmp_domains. Task behaviour is likely to change over time. Tasks running in a less capable hmp_domain may change to become more demanding and should therefore be migrated up. They are unlikely go through the select_task_rq_fair() path anytime soon and therefore need special attention. This patch introduces a period check (SCHED_TICK) of the currently running task on all runqueues and sets up a forced migration using stop_machine_no_wait() if the task needs to be migrated. Ideally, this should not be implemented by polling all runqueues. Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11sched: Task placement for heterogeneous systems based on task load-trackingMorten Rasmussen
This patch introduces the basic SCHED_HMP infrastructure. Each class of cpus is represented by a hmp_domain and tasks will only be moved between these domains when their load profiles suggest it is beneficial. SCHED_HMP relies heavily on the task load-tracking introduced in Paul Turners fair group scheduling patch set: <https://lkml.org/lkml/2012/8/23/267> SCHED_HMP requires that the platform implements arch_get_hmp_domains() which should set up the platform specific list of hmp_domains. It is also assumed that the platform disables SD_LOAD_BALANCE for the appropriate sched_domains. Tasks placement takes place every time a task is to be inserted into a runqueue based on its load history. The task placement decision is based on load thresholds. There are no restrictions on the number of hmp_domains, however, multiple (>2) has not been tested and the up/down migration policy is rather simple. Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11sched: entity load-tracking load_avg_ratioMorten Rasmussen
This patch adds load_avg_ratio to each task. The load_avg_ratio is a variant of load_avg_contrib which is not scaled by the task priority. It is calculated like this: runnable_avg_sum * NICE_0_LOAD / (runnable_avg_period + 1). Signed-off-by: Morten Rasmussen <Morten.Rasmussen@arm.com>
2013-02-11sched: implement usage trackingPaul Turner
With the frame-work for runnable tracking now fully in place. Per-entity usage tracking is a simple and low-overhead addition. Signed-off-by: Paul Turner <pjt@google.com> Reviewed-by: Ben Segall <bsegall@google.com>
2013-02-11ARM: hw_breakpoint: Debug powerdown support for self-hosted debugDietmar Eggemann
This patch introduces debug powerdown support for self-hosted debug for v7 and v7.1 debug architecture for a SinglePower system, i.e. a system without a separate core and debug power domain. On a SinglePower system the OS Lock is lost over a powerdown. If CONFIG_CPU_PM is set the new function pm_init() registers hw_breakpoint with CPU PM for a system supporting OS Save and Restore. Receiving a CPU PM EXIT notifier indicates that a single CPU has exited a low power state. A call to reset_ctrl_regs() is hooked into the CPU PM EXIT notifier chain. This function makes sure that the sticky power-down is clear (only v7 debug), the OS Double Lock is clear (only v7.1 debug) and it clears the OS Lock for v7 debug (for a system supporting OS Save and Restore) and v7.1 debug. Furthermore, it clears any vector-catch events and all breakpoint/watchpoint control/value registers for v7 and v7.1 debug. Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2013-02-11ARM: hw_breakpoint: Check function for OS Save and Restore mechanismDietmar Eggemann
v7 debug introduced OS Save and Restore mechanism. On a v7 debug SinglePower system, i.e a system without a separate core and debug power domain, which does not support external debug over powerdown, it is implementation defined whether OS Save and Restore is implemented. v7.1 debug requires OS Save and Restore mechanism. v6 debug and v6.1 debug do not implement it. A new global variable bool has_ossr is introduced and is determined in arch_hw_breakpoint_init() like debug_arch or the number of BRPs/WRPs. The logic how to check if OS Save and Restore is supported has changed with this patch. In reset_ctrl_regs() a mask consisting of OSLM[1] (OSLSR.3) and OSLM[0] (OSLSR.0) was used to check if the system supports OS Save and Restore. In the new function core_has_os_save_restore() only OSLM[0] is used. It is not necessary to check OSLM[1] too since it is v7.1 debug specific and v7.1 debug requires OS Save and Restore and thus OS Lock. Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2013-02-11ARM: perf: save/restore pmu registers in pm notifierSudeep KarkadaNagesha
This adds core support for saving and restoring CPU PMU registers for suspend/resume support i.e. deeper C-states in cpuidle terms. This patch adds support only to ARMv7 PMU registers save/restore. It needs to be extended to xscale and ARMv6 if needed. Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
2013-02-11ARM: perf: remove spaces in CPU PMU namesSudeep KarkadaNagesha
The userspace perf tool provides options to specify PMU names from command line for the event. An example of pmu event syntax would be (<pmu_name>/<config>/<modifier>) However the parser in the perf tool breaks the tokens at spacesand fails to identify the PMU name with spaces correctly. This patch removes spaces in the ARMv7 CPU PMU names. Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
2013-02-11ARM: perf: set cpu affinity for the irqs correctlySudeep KarkadaNagesha
This patch sets the cpu affinity for the perf IRQs in the logical order within the cluster. However interupts are assumed to be specified in the same logical order within the cluster. Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
2013-02-11ARM: perf: set cpu affinity to support multiple PMUsSudeep KarkadaNagesha
In a system with multiple heterogeneous CPU PMUs and each PMUs can handle events on a subset of CPUs, probably belonging a the same cluster. This patch introduces a cpumask to track which CPUs each PMU supports. It also updates armpmu_event_init to reject cpu-specific events being initialised for unsupported CPUs. Since process-specific events can be initialised for all the CPU PMUs,armpmu_start/stop/add are modified to prevent from being added on unsupported CPUs. Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
2013-02-11ARM: perf: register CPU PMUs with idr typesSudeep KarkadaNagesha
In order to support multiple, heterogeneous CPU PMUs and distinguish them, they cannot be registered as PERF_TYPE_RAW type. Instead we can get perf core to allocate a new idr type id for each PMU. Userspace applications can refer sysfs entried to find a PMU's type, which can then be used in tracking events on individual PMUs. Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
2013-02-11ARM: perf: replace global CPU PMU pointer with per-cpu pointersSudeep KarkadaNagesha
A single global CPU PMU pointer is not useful in a system with multiple, heterogeneous CPU PMUs as we need to access the relevant PMU depending on the current CPU. This patch replaces the single global CPU PMU pointer with per-cpu pointers and changes the OProfile accessors to refer to the PMU affine to CPU0. Signed-off-by: Sudeep KarkadaNagesha <Sudeep.KarkadaNagesha@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com>
2013-02-11ARM: kernel: provide cluster to logical cpu mask mapping APILorenzo Pieralisi
Some device drivers like PMU require to retrieve the logical cpu mask that corresponds to a given cluster id. This patch provides a hook in the topology code that, given an existing cluster id as input, initializes the corresponding cpumask passed as a pointer, reusing all existing topology information required by sched domains in the kernel. Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
2013-02-09Linux 3.8-rc7Linus Torvalds
2013-02-09Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-armLinus Torvalds
Pull ARM fixes from Russell King: "I was going to hold these off until v3.8 was out, and send them with a stable tag, but as everyone else is pushing much bigger fixes which Linus is accepting, let's save people from the hastle of having to patch v3.8 back into working or use a stable kernel. Looking at the diffstat, this really is high value for its size; this is miniscule compared to how the -rc6 to tip diffstat currently looks. So, four patches in this set: - Punit Agrawal reports that the kernel no longer boots on MPCore due to a new assumption made in the GIC code which isn't true of earlier GIC designs. This is the biggest change in this set. - Punit's boot log also revealed a bunch of WARN_ON() dumps caused by the DT-ification of the GIC support without fixing up non-DT Realview - which now sees a greater number of interrupts than it did before. - A fix for the DMA coherent code from Marek which uses the wrong check for atomic allocations; this can result in spinlock lockups or other nasty effects. - A fix from Will, which will affect all Android based platforms if not applied (which use the 2G:2G VM split) - this causes particularly 'make' to misbehave unless this bug is fixed." * 'fixes' of git://git.linaro.org/people/rmk/linux-arm: ARM: 7641/1: memory: fix broken mmap by ensuring TASK_UNMAPPED_BASE is aligned ARM: DMA mapping: fix bad atomic test ARM: realview: ensure that we have sufficient IRQs available ARM: GIC: fix GIC cpumask initialization
2013-02-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds
Pull networking fixes from David Miller: 1) Revert iwlwifi reclaimed packet tracking, it causes problems for a bunch of folks. From Emmanuel Grumbach. 2) Work limiting code in brcmsmac wifi driver can clear tx status without processing the event. From Arend van Spriel. 3) rtlwifi USB driver processes wrong SKB, fix from Larry Finger. 4) l2tp tunnel delete can race with close, fix from Tom Parkin. 5) pktgen_add_device() failures are not checked at all, fix from Cong Wang. 6) Fix unintentional removal of carrier off from tun_detach(), otherwise we confuse userspace, from Michael S. Tsirkin. 7) Don't leak socket reference counts and ubufs in vhost-net driver, from Jason Wang. 8) vmxnet3 driver gets it's initial carrier state wrong, fix from Neil Horman. 9) Protect against USB networking devices which spam the host with 0 length frames, from Bjørn Mork. 10) Prevent neighbour overflows in ipv6 for locally destined routes, from Marcelo Ricardo. This is the best short-term fix for this, a longer term fix has been implemented in net-next. 11) L2TP uses ipv4 datagram routines in it's ipv6 code, whoops. This mistake is largely because the ipv6 functions don't even have some kind of prefix in their names to suggest they are ipv6 specific. From Tom Parkin. 12) Check SYN packet drops properly in tcp_rcv_fastopen_synack(), from Yuchung Cheng. 13) Fix races and TX skb freeing bugs in via-rhine's NAPI support, from Francois Romieu and your's truly. 14) Fix infinite loops and divides by zero in TCP congestion window handling, from Eric Dumazet, Neal Cardwell, and Ilpo Järvinen. 15) AF_PACKET tx ring handling can leak kernel memory to userspace, fix from Phil Sutter. 16) Fix error handling in ipv6 GRE tunnel transmit, from Tommi Rantala. 17) Protect XEN netback driver against hostile frontend putting garbage into the rings, don't leak pages in TX GOP checking, and add proper resource releasing in error path of xen_netbk_get_requests(). From Ian Campbell. 18) SCTP authentication keys should be cleared out and released with kzfree(), from Daniel Borkmann. 19) L2TP is a bit too clever trying to maintain skb->truesize, and ends up corrupting socket memory accounting to the point where packet sending is halted indefinitely. Just remove the adjustments entirely, they aren't really needed. From Eric Dumazet. 20) ATM Iphase driver uses a data type with the same name as the S390 headers, rename to fix the build. From Heiko Carstens. 21) Fix a typo in copying the inner network header offset from one SKB to another, from Pravin B Shelar. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits) net: sctp: sctp_endpoint_free: zero out secret key data net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfree atm/iphase: rename fregt_t -> ffreg_t net: usb: fix regression from FLAG_NOARP code l2tp: dont play with skb->truesize net: sctp: sctp_auth_key_put: use kzfree instead of kfree netback: correct netbk_tx_err to handle wrap around. xen/netback: free already allocated memory on failure in xen_netbk_get_requests xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop. xen/netback: shutdown the ring if it contains garbage. net: qmi_wwan: add more Huawei devices, including E320 net: cdc_ncm: add another Huawei vendor specific device ipv6/ip6_gre: fix error case handling in ip6gre_tunnel_xmit() tcp: fix for zero packets_in_flight was too broad brcmsmac: rework of mac80211 .flush() callback operation ssb: unregister gpios before unloading ssb bcma: unregister gpios before unloading bcma rtlwifi: Fix scheduling while atomic bug net: usbnet: fix tx_dropped statistics tcp: ipv6: Update MIB counters for drops ...
2013-02-08Merge branch 'sctp_keys'David S. Miller
Daniel Borkmann says: ==================== Cryptographically used keys should be zeroed out when our session ends resp. memory is freed, thus do not leave them somewhere in the memory. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08net: sctp: sctp_endpoint_free: zero out secret key dataDaniel Borkmann
On sctp_endpoint_destroy, previously used sensitive keying material should be zeroed out before the memory is returned, as we already do with e.g. auth keys when released. Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Acked-by: Vlad Yasevich <vyasevic@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfreeDaniel Borkmann
In sctp_setsockopt_auth_key, we create a temporary copy of the user passed shared auth key for the endpoint or association and after internal setup, we free it right away. Since it's sensitive data, we should zero out the key before returning the memory back to the allocator. Thus, use kzfree instead of kfree, just as we do in sctp_auth_key_put(). Signed-off-by: Daniel Borkmann <dborkman@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08atm/iphase: rename fregt_t -> ffreg_tHeiko Carstens
We have conflicting type qualifiers for "freg_t" in s390's ptrace.h and the iphase atm device driver, which causes the compile error below. Unfortunately the s390 typedef can't be renamed, since it's a user visible api, nor can I change the include order in s390 code to avoid the conflict. So simply rename the iphase typedef to a new name. Fixes this compile error: In file included from drivers/atm/iphase.c:66:0: drivers/atm/iphase.h:639:25: error: conflicting type qualifiers for 'freg_t' In file included from next/arch/s390/include/asm/ptrace.h:9:0, from next/arch/s390/include/asm/lowcore.h:12, from next/arch/s390/include/asm/thread_info.h:30, from include/linux/thread_info.h:54, from include/linux/preempt.h:9, from include/linux/spinlock.h:50, from include/linux/seqlock.h:29, from include/linux/time.h:5, from include/linux/stat.h:18, from include/linux/module.h:10, from drivers/atm/iphase.c:43: next/arch/s390/include/uapi/asm/ptrace.h:197:3: note: previous declaration of 'freg_t' was here Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by: chas williams - CONTRACTOR <chas@cmf.nrl.navy.mil> Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-08ARM: 7641/1: memory: fix broken mmap by ensuring TASK_UNMAPPED_BASE is alignedWill Deacon
We have received multiple reports of mmap failures when running with a 2:2 vm split. These manifest as either -EINVAL with a non page-aligned address (ending 0xaaa) or a SEGV, depending on the application. The issue is commonly observed in children of make, which appears to use bottom-up mmap (assumedly because it changes the stack rlimit). Further investigation reveals that this regression was triggered by 394ef6403abc ("mm: use vm_unmapped_area() on arm architecture"), whereby TASK_UNMAPPED_BASE is no longer page-aligned for bottom-up mmap, causing get_unmapped_area to choke on misaligned addressed. This patch fixes the problem by defining TASK_UNMAPPED_BASE in terms of TASK_SIZE and explicitly aligns the result to 16M, matching the other end of the heap. Acked-by: Nicolas Pitre <nico@linaro.org> Reported-by: Steve Capper <steve.capper@arm.com> Reported-by: Jean-Francois Moine <moinejf@free.fr> Reported-by: Christoffer Dall <cdall@cs.columbia.edu> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-02-08ARM: DMA mapping: fix bad atomic testRussell King
Realview fails to boot with this warning: BUG: spinlock lockup suspected on CPU#0, init/1 lock: 0xcf8bde10, .magic: dead4ead, .owner: init/1, .owner_cpu: 0 Backtrace: [<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:cf8bde10 r5:cf83d1c0 r4:cf8bde10 r3:cf83d1c0 [<c03294d0>] (dump_stack+0x0/0x1c) from [<c018926c>] (spin_dump+0x84/0x98) [<c01891e8>] (spin_dump+0x0/0x98) from [<c0189460>] (do_raw_spin_lock+0x100/0x198) [<c0189360>] (do_raw_spin_lock+0x0/0x198) from [<c032cbac>] (_raw_spin_lock+0x3c/0x44) [<c032cb70>] (_raw_spin_lock+0x0/0x44) from [<c01c9224>] (pl011_console_write+0xe8/0x11c) [<c01c913c>] (pl011_console_write+0x0/0x11c) from [<c002aea8>] (call_console_drivers.clone.7+0xdc/0x104) [<c002adcc>] (call_console_drivers.clone.7+0x0/0x104) from [<c002b320>] (console_unlock+0x2e8/0x454) [<c002b038>] (console_unlock+0x0/0x454) from [<c002b8b4>] (vprintk_emit+0x2d8/0x594) [<c002b5dc>] (vprintk_emit+0x0/0x594) from [<c0329718>] (printk+0x3c/0x44) [<c03296dc>] (printk+0x0/0x44) from [<c002929c>] (warn_slowpath_common+0x28/0x6c) [<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c) [<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c0070ab0>] (lockdep_trace_alloc+0xd8/0xf0) [<c00709d8>] (lockdep_trace_alloc+0x0/0xf0) from [<c00c0850>] (kmem_cache_alloc+0x24/0x11c) [<c00c082c>] (kmem_cache_alloc+0x0/0x11c) from [<c00bb044>] (__get_vm_area_node.clone.24+0x7c/0x16c) [<c00bafc8>] (__get_vm_area_node.clone.24+0x0/0x16c) from [<c00bb7b8>] (get_vm_area_caller+0x48/0x54) [<c00bb770>] (get_vm_area_caller+0x0/0x54) from [<c0020064>] (__alloc_remap_buffer.clone.15+0x38/0xb8) [<c002002c>] (__alloc_remap_buffer.clone.15+0x0/0xb8) from [<c0020244>] (__dma_alloc+0x160/0x2c8) [<c00200e4>] (__dma_alloc+0x0/0x2c8) from [<c00204d8>] (arm_dma_alloc+0x88/0xa0)[<c0020450>] (arm_dma_alloc+0x0/0xa0) from [<c00beb00>] (dma_pool_alloc+0xcc/0x1a8) [<c00bea34>] (dma_pool_alloc+0x0/0x1a8) from [<c01a9d14>] (pl08x_fill_llis_for_desc+0x28/0x568) [<c01a9cec>] (pl08x_fill_llis_for_desc+0x0/0x568) from [<c01aab8c>] (pl08x_prep_slave_sg+0x258/0x3b0) [<c01aa934>] (pl08x_prep_slave_sg+0x0/0x3b0) from [<c01c9f74>] (pl011_dma_tx_refill+0x140/0x288) [<c01c9e34>] (pl011_dma_tx_refill+0x0/0x288) from [<c01ca748>] (pl011_start_tx+0xe4/0x120) [<c01ca664>] (pl011_start_tx+0x0/0x120) from [<c01c54a4>] (__uart_start+0x48/0x4c) [<c01c545c>] (__uart_start+0x0/0x4c) from [<c01c632c>] (uart_start+0x2c/0x3c) [<c01c6300>] (uart_start+0x0/0x3c) from [<c01c795c>] (uart_write+0xcc/0xf4) [<c01c7890>] (uart_write+0x0/0xf4) from [<c01b0384>] (n_tty_write+0x1c0/0x3e4) [<c01b01c4>] (n_tty_write+0x0/0x3e4) from [<c01acfe8>] (tty_write+0x144/0x240) [<c01acea4>] (tty_write+0x0/0x240) from [<c01ad17c>] (redirected_tty_write+0x98/0xac) [<c01ad0e4>] (redirected_tty_write+0x0/0xac) from [<c00c371c>] (vfs_write+0xbc/0x150) [<c00c3660>] (vfs_write+0x0/0x150) from [<c00c39c0>] (sys_write+0x4c/0x78) [<c00c3974>] (sys_write+0x0/0x78) from [<c0014460>] (ret_fast_syscall+0x0/0x3c) This happens because the DMA allocation code is not respecting atomic allocations correctly. GFP flags should not be tested for GFP_ATOMIC to determine if an atomic allocation is being requested. GFP_ATOMIC is not a flag but a value. The GFP bitmask flags are all prefixed with __GFP_. The rest of the kernel tests for __GFP_WAIT not being set to indicate an atomic allocation. We need to do the same. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-02-08ARM: realview: ensure that we have sufficient IRQs availableRussell King
Realview EB with a rev B MPcore tile results in lots of warnings at boot because it can't allocate enough IRQs. Fix this by increasing the number of available IRQs. WARNING: at /home/rmk/git/linux-rmk/arch/arm/common/gic.c:757 gic_init_bases+0x12c/0x2ec() Cannot allocate irq_descs @ IRQ96, assuming pre-allocated Modules linked in: Backtrace: [<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000002f5 r5:c042c62c r4:c044ff40 r3:c045f240 [<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c) [<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029384>] (warn_slowpath_fmt+0x38/0x40) [<c002934c>] (warn_slowpath_fmt+0x0/0x40) from [<c042c62c>] (gic_init_bases+0x12c/0x2ec) [<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8) [<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24) [<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300) [<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070) ---[ end trace 1b75b31a2719ed1c ]--- ------------[ cut here ]------------ WARNING: at /home/rmk/git/linux-rmk/kernel/irq/irqdomain.c:234 irq_domain_add_legacy+0x80/0x140() Modules linked in: Backtrace: [<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000000ea r5:c0081a38 r4:00000000 r3:c045f240 [<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c) [<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c) [<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c0081a38>] (irq_domain_add_legacy+0x80/0x140) [<c00819b8>] (irq_domain_add_legacy+0x0/0x140) from [<c042c64c>] (gic_init_bases+0x14c/0x2ec) [<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8) [<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24) [<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300) [<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070) ---[ end trace 1b75b31a2719ed1d ]--- ------------[ cut here ]------------ WARNING: at /home/rmk/git/linux-rmk/arch/arm/common/gic.c:762 gic_init_bases+0x170/0x2ec() Modules linked in: Backtrace: [<c00185d8>] (dump_backtrace+0x0/0x10c) from [<c03294e8>] (dump_stack+0x18/0x1c) r6:000002fa r5:c042c670 r4:00000000 r3:c045f240 [<c03294d0>] (dump_stack+0x0/0x1c) from [<c00292c8>] (warn_slowpath_common+0x54/0x6c) [<c0029274>] (warn_slowpath_common+0x0/0x6c) from [<c0029304>] (warn_slowpath_null+0x24/0x2c) [<c00292e0>] (warn_slowpath_null+0x0/0x2c) from [<c042c670>] (gic_init_bases+0x170/0x2ec) [<c042c500>] (gic_init_bases+0x0/0x2ec) from [<c042cdc8>] (gic_init_irq+0x8c/0xd8) [<c042cd3c>] (gic_init_irq+0x0/0xd8) from [<c042827c>] (init_IRQ+0x1c/0x24) [<c0428260>] (init_IRQ+0x0/0x24) from [<c04256c8>] (start_kernel+0x1a4/0x300) [<c0425524>] (start_kernel+0x0/0x300) from [<70008070>] (0x70008070) ---[ end trace 1b75b31a2719ed1e ]--- Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-02-08ARM: GIC: fix GIC cpumask initializationRussell King
Punit Agrawal reports: > I was trying to boot 3.8-rc5 on Realview EB 11MPCore using > realview-smp_defconfig as a starting point but the kernel failed to > progress past the log below (config attached). > > Pawel suggested I try reverting 384a290283f - "ARM: gic: use a private > mapping for CPU target interfaces" that you've authored. With this > commit reverted the kernel boots. > > I am not quite sure why the commit breaks 11MPCore but Pawel (cc'd) > might be able to shed light on that. Some early GIC implementations return zero for the first distributor CPU routing register. This means we can't rely on that telling us which CPU interface we're connected to. We know that these platforms implement PPIs for IRQs 29-31 - but we shouldn't assume that these will always be populated. So, instead, scan for a non-zero CPU routing register in the first 32 IRQs and use that as our CPU mask. Reported-by: Punit Agrawal <punit.agrawal@arm.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2013-02-08Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds
Pull drm regression fix from Dave Airlie: "This one fixes a sleep while locked regression that was introduced earlier in 3.8." * 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: drm/ttm: fix fence locking in ttm_buffer_object_transfer, 2nd try