path: root/Documentation/cdrom/cdu31a
diff options
Diffstat (limited to 'Documentation/cdrom/cdu31a')
1 files changed, 196 insertions, 0 deletions
diff --git a/Documentation/cdrom/cdu31a b/Documentation/cdrom/cdu31a
new file mode 100644
index 000000000000..c0667da09c00
--- /dev/null
+++ b/Documentation/cdrom/cdu31a
@@ -0,0 +1,196 @@
+ CDU31A/CDU33A Driver Info
+ -------------------------
+Information on the Sony CDU31A/CDU33A CDROM driver for the Linux
+ Corey Minyard (minyard@metronet.com)
+ Colossians 3:17
+Crude Table of Contents
+ Setting Up the Hardware
+ Configuring the Kernel
+ Configuring as a Module
+ Driver Special Features
+This device driver handles Sony CDU31A/CDU33A CDROM drives and
+provides a complete block-level interface as well as an ioctl()
+interface as specified in include/linux/cdrom.h). With this
+interface, CDROMs can be accessed, standard audio CDs can be played
+back normally, and CD audio information can be read off the drive.
+Note that this will only work for CDU31A/CDU33A drives. Some vendors
+market their drives as CDU31A compatible. They lie. Their drives are
+really CDU31A hardware interface compatible (they can plug into the
+same card). They are not software compatible.
+Setting Up the Hardware
+The CDU31A driver is unable to safely tell if an interface card is
+present that it can use because the interface card does not announce
+its presence in any way besides placing 4 I/O locations in memory. It
+used to just probe memory and attempt commands, but Linus wisely asked
+me to remove that because it could really screw up other hardware in
+the system.
+Because of this, you must tell the kernel where the drive interface
+is, what interrupts are used, and possibly if you are on a PAS-16
+If you have the Sony CDU31A/CDU33A drive interface card, the following
+diagram will help you set it up. If you have another card, you are on
+your own. You need to make sure that the I/O address and interrupt is
+not used by another card in the system. You will need to know the I/O
+address and interrupt you have set. Note that use of interrupts is
+highly recommended, if possible, it really cuts down on CPU used.
+Unfortunately, most soundcards do not support interrupts for their
+CDROM interfaces. By default, the Sony interface card comes with
+interrupts disabled.
+ +----------+-----------------+----------------------+
+ | JP1 | 34 Pin Conn | |
+ | JP2 +-----------------+ |
+ | JP3 |
+ | JP4 |
+ | +--+
+ | | +-+
+ | | | | External
+ | | | | Connector
+ | | | |
+ | | +-+
+ | +--+
+ | |
+ | +--------+
+ | |
+ +------------------------------------------+
+ JP1 sets the Base Address, using the following settings:
+ Address Pin 1 Pin 2
+ ------- ----- -----
+ 0x320 Short Short
+ 0x330 Short Open
+ 0x340 Open Short
+ 0x360 Open Open
+ JP2 and JP3 configure the DMA channel; they must be set the same.
+ DMA Pin 1 Pin 2 Pin 3
+ --- ----- ----- -----
+ 1 On Off On
+ 2 Off On Off
+ 3 Off Off On
+ JP4 Configures the IRQ:
+ IRQ Pin 1 Pin 2 Pin 3 Pin 4
+ --- ----- ----- ----- -----
+ 3 Off Off On Off
+ 4 Off Off* Off On
+ 5 On Off Off Off
+ 6 Off On Off Off
+ The documentation states to set this for interrupt
+ 4, but I think that is a mistake.
+Note that if you have another interface card, you will need to look at
+the documentation to find the I/O base address. This is specified to
+the SLCD.SYS driver for DOS with the /B: parameter, so you can look at
+you DOS driver setup to find the address, if necessary.
+Configuring the Kernel
+You must tell the kernel where the drive is at boot time. This can be
+done at the Linux boot prompt, by using LILO, or by using Bootlin.
+Note that this is no substitute for HOWTOs and LILO documentation, if
+you are confused please read those for info on bootline configuration
+and LILO.
+At the linux boot prompt, press the ALT key and add the following line
+after the boot name (you can let the kernel boot, it will tell you the
+default boot name while booting):
+ cdu31a=<base address>,<interrupt>[,PAS]
+The base address needs to have "0x" in front of it, since it is in
+hex. For instance, to configure a drive at address 320 on interrupt 5,
+use the following:
+ cdu31a=0x320,5
+I use the following boot line:
+ cdu31a=0x1f88,0,PAS
+because I have a PAS-16 which does not support interrupt for the
+CDU31A interface.
+Adding this as an append line at the beginning of the /etc/lilo.conf
+file will set it for lilo configurations. I have the following as the
+first line in my lilo.conf file:
+ append="cdu31a=0x1f88,0"
+I'm not sure how to set up Bootlin (I have never used it), if someone
+would like to fill in this section please do.
+Configuring as a Module
+The driver supports loading as a module. However, you must specify
+the boot address and interrupt on the boot line to insmod. You can't
+use modprobe to load it, since modprobe doesn't support setting
+Anyway, I use the following line to load my driver as a module
+ /sbin/insmod /lib/modules/`uname -r`/misc/cdu31a.o cdu31a_port=0x1f88
+You can set the following variables in the driver:
+ cdu31a_port=<I/O address> - sets the base I/O. If hex, put 0x in
+ front of it. This must be specified.
+ cdu31a_irq=<interrupt> - Sets the interrupt number. Leaving this
+ off will turn interrupts off.
+Driver Special Features
+This section describes features beyond the normal audio and CD-ROM
+functions of the drive.
+2048 byte buffer mode
+If a disk is mounted with -o block=2048, data is copied straight from
+the drive data port to the buffer. Otherwise, the readahead buffer
+must be involved to hold the other 1K of data when a 1K block
+operation is done. Note that with 2048 byte blocks you cannot execute
+files from the CD.
+XA compatibility
+The driver should support XA disks for both the CDU31A and CDU33A. It
+does this transparently, the using program doesn't need to set it.
+A multi-session disk looks just like a normal disk to the user. Just
+mount one normally, and all the data should be there. A special
+thanks to Koen for help with this!
+Raw sector I/O
+Using the CDROMREADAUDIO it is possible to read raw audio and data
+tracks. Both operations return 2352 bytes per sector. On the data
+tracks, the first 12 bytes is not returned by the drive and the value
+of that data is indeterminate.