diff options
8 files changed, 8 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
index f98d4c5b5cc..296eb453612 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
@@ -26,7 +26,7 @@ Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
- pinctrl-names: Should contain only one value - "default".
Optional properties:
- - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
+ - samsung,i2c-slave-addr: Slave address in multi-master environment. If not
specified, default value is 0.
- samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
specified, the default value in Hz is 100000.
diff --git a/Documentation/devicetree/bindings/leds/tca6507.txt b/Documentation/devicetree/bindings/leds/tca6507.txt
index 2b6693b972f..80ff3dfb1f3 100644
--- a/Documentation/devicetree/bindings/leds/tca6507.txt
+++ b/Documentation/devicetree/bindings/leds/tca6507.txt
@@ -1,4 +1,4 @@
-LEDs conected to tca6507
+LEDs connected to tca6507
Required properties:
- compatible : should be : "ti,tca6507".
diff --git a/Documentation/devicetree/bindings/metag/meta-intc.txt b/Documentation/devicetree/bindings/metag/meta-intc.txt
index 8c47dcbfabc..80994adab39 100644
--- a/Documentation/devicetree/bindings/metag/meta-intc.txt
+++ b/Documentation/devicetree/bindings/metag/meta-intc.txt
@@ -12,7 +12,7 @@ Required properties:
handle 32 interrupt sources).
- interrupt-controller: The presence of this property identifies the node
- as an interupt controller. No property value shall be defined.
+ as an interrupt controller. No property value shall be defined.
- #interrupt-cells: Specifies the number of cells needed to encode an
interrupt source. The type shall be a <u32> and the value shall be 2.
diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
index bc50899e0c8..648d60eb9fd 100644
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
@@ -1,6 +1,6 @@
* Atmel AT91 Pinmux Controller
-The AT91 Pinmux Controler, enables the IC
+The AT91 Pinmux Controller, enables the IC
to share one PAD to several functional blocks. The sharing is done by
multiplexing the PAD input/output signals. For each PAD there are up to
8 muxing options (called periph modes). Since different modules require
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt
index 8edc20e1b09..2569866c692 100644
--- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt
@@ -5,7 +5,7 @@ controller, and pinmux/control device.
Required properties:
- compatible: "brcm,bcm2835-gpio"
-- reg: Should contain the physical address of the GPIO module's registes.
+- reg: Should contain the physical address of the GPIO module's registers.
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells : Should be two. The first cell is the pin number and the
second cell is used to specify optional parameters:
diff --git a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt
index 9a599d27bd7..0347d8350d9 100644
--- a/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt
+++ b/Documentation/devicetree/bindings/power_supply/qnap-poweroff.txt
@@ -2,7 +2,7 @@
QNAP NAS devices have a microcontroller controlling the main power
supply. This microcontroller is connected to UART1 of the Kirkwood and
-Orion5x SoCs. Sending the charactor 'A', at 19200 baud, tells the
+Orion5x SoCs. Sending the character 'A', at 19200 baud, tells the
microcontroller to turn the power off. This driver adds a handler to
pm_power_off which is called to turn the power off.
diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
index 9fd69a18b0b..9e5e51d7886 100644
--- a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
@@ -28,7 +28,7 @@ Required properties:
safe operating voltage).
If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
- property is specified, then all the eigth voltage values for the
+ property is specified, then all the eight voltage values for the
'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified.
Optional properties:
diff --git a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt
index 033194934f6..adddcf47c79 100644
--- a/Documentation/devicetree/bindings/usb/samsung-usbphy.txt
+++ b/Documentation/devicetree/bindings/usb/samsung-usbphy.txt
@@ -4,7 +4,7 @@ The Samsung's phy transceiver is used for controlling usb phy for
s3c-hsotg as well as ehci-s5p and ohci-exynos usb controllers
across Samsung SOCs.
TODO: Adding the PHY binding with controller(s) according to the under
-developement generic PHY driver.
+development generic PHY driver.
Required properties: