aboutsummaryrefslogtreecommitdiff
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt12
-rw-r--r--Documentation/filesystems/overlayfs.txt5
-rw-r--r--Documentation/i2c/busses/i2c-i8011
3 files changed, 12 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
index b878a1e305af..ed1456f5c94d 100644
--- a/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
+++ b/Documentation/devicetree/bindings/mmc/marvell,xenon-sdhci.txt
@@ -16,11 +16,13 @@ Required Properties:
- clocks:
Array of clocks required for SDHC.
- Require at least input clock for Xenon IP core.
+ Require at least input clock for Xenon IP core. For Armada AP806 and
+ CP110, the AXI clock is also mandatory.
- clock-names:
Array of names corresponding to clocks property.
The input clock for Xenon IP core should be named as "core".
+ The input clock for the AXI bus must be named as "axi".
- reg:
* For "marvell,armada-3700-sdhci", two register areas.
@@ -106,8 +108,8 @@ Example:
compatible = "marvell,armada-ap806-sdhci";
reg = <0xaa0000 0x1000>;
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>
- clocks = <&emmc_clk>;
- clock-names = "core";
+ clocks = <&emmc_clk>,<&axi_clk>;
+ clock-names = "core", "axi";
bus-width = <4>;
marvell,xenon-phy-slow-mode;
marvell,xenon-tun-count = <11>;
@@ -126,8 +128,8 @@ Example:
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>
vqmmc-supply = <&sd_vqmmc_regulator>;
vmmc-supply = <&sd_vmmc_regulator>;
- clocks = <&sdclk>;
- clock-names = "core";
+ clocks = <&sdclk>, <&axi_clk>;
+ clock-names = "core", "axi";
bus-width = <4>;
marvell,xenon-tun-count = <9>;
};
diff --git a/Documentation/filesystems/overlayfs.txt b/Documentation/filesystems/overlayfs.txt
index 36f528a7fdd6..8caa60734647 100644
--- a/Documentation/filesystems/overlayfs.txt
+++ b/Documentation/filesystems/overlayfs.txt
@@ -210,8 +210,11 @@ path as another overlay mount and it may use a lower layer path that is
beneath or above the path of another overlay lower layer path.
Using an upper layer path and/or a workdir path that are already used by
-another overlay mount is not allowed and will fail with EBUSY. Using
+another overlay mount is not allowed and may fail with EBUSY. Using
partially overlapping paths is not allowed but will not fail with EBUSY.
+If files are accessed from two overlayfs mounts which share or overlap the
+upper layer and/or workdir path the behavior of the overlay is undefined,
+though it will not result in a crash or deadlock.
Mounting an overlay using an upper layer path, where the upper layer path
was previously used by another mounted overlay in combination with a
diff --git a/Documentation/i2c/busses/i2c-i801 b/Documentation/i2c/busses/i2c-i801
index 0500193434cb..d47702456926 100644
--- a/Documentation/i2c/busses/i2c-i801
+++ b/Documentation/i2c/busses/i2c-i801
@@ -36,6 +36,7 @@ Supported adapters:
* Intel Gemini Lake (SOC)
* Intel Cannon Lake-H (PCH)
* Intel Cannon Lake-LP (PCH)
+ * Intel Cedar Fork (PCH)
Datasheets: Publicly available at the Intel website
On Intel Patsburg and later chipsets, both the normal host SMBus controller