path: root/Documentation/x86_64/boot-options.txt
diff options
Diffstat (limited to 'Documentation/x86_64/boot-options.txt')
1 files changed, 180 insertions, 0 deletions
diff --git a/Documentation/x86_64/boot-options.txt b/Documentation/x86_64/boot-options.txt
new file mode 100644
index 000000000000..44b6eea60ece
--- /dev/null
+++ b/Documentation/x86_64/boot-options.txt
@@ -0,0 +1,180 @@
+AMD64 specific boot options
+There are many others (usually documented in driver documentation), but
+only the AMD64 specific ones are listed here.
+Machine check
+ mce=off disable machine check
+ nomce (for compatibility with i386): same as mce=off
+ Everything else is in sysfs now.
+ apic Use IO-APIC. Default
+ noapic Don't use the IO-APIC.
+ disableapic Don't use the local APIC
+ nolapic Don't use the local APIC (alias for i386 compatibility)
+ pirq=... See Documentation/i386/IO-APIC.txt
+ noapictimer Don't set up the APIC timer
+Early Console
+ syntax: earlyprintk=vga
+ earlyprintk=serial[,ttySn[,baudrate]]
+ The early console is useful when the kernel crashes before the
+ normal console is initialized. It is not enabled by
+ default because it has some cosmetic problems.
+ Append ,keep to not disable it when the real console takes over.
+ Only vga or serial at a time, not both.
+ Currently only ttyS0 and ttyS1 are supported.
+ Interaction with the standard serial driver is not very good.
+ The VGA output is eventually overwritten by the real console.
+ notsc
+ Don't use the CPU time stamp counter to read the wall time.
+ This can be used to work around timing problems on multiprocessor systems
+ with not properly synchronized CPUs. Only useful with a SMP kernel
+ report_lost_ticks
+ Report when timer interrupts are lost because some code turned off
+ interrupts for too long.
+ nmi_watchdog=NUMBER[,panic]
+ NUMBER can be:
+ 0 don't use an NMI watchdog
+ 1 use the IO-APIC timer for the NMI watchdog
+ 2 use the local APIC for the NMI watchdog using a performance counter. Note
+ This will use one performance counter and the local APIC's performance
+ vector.
+ When panic is specified panic when an NMI watchdog timeout occurs.
+ This is useful when you use a panic=... timeout and need the box
+ quickly up again.
+ nohpet
+ Don't use the HPET timer.
+Idle loop
+ idle=poll
+ Don't do power saving in the idle loop using HLT, but poll for rescheduling
+ event. This will make the CPUs eat a lot more power, but may be useful
+ to get slightly better performance in multiprocessor benchmarks. It also
+ makes some profiling using performance counters more accurate.
+ reboot=b[ios] | t[riple] | k[bd] [, [w]arm | [c]old]
+ bios Use the CPU reboto vector for warm reset
+ warm Don't set the cold reboot flag
+ cold Set the cold reboot flag
+ triple Force a triple fault (init)
+ kbd Use the keyboard controller. cold reset (default)
+ Using warm reset will be much faster especially on big memory
+ systems because the BIOS will not go through the memory check.
+ Disadvantage is that not all hardware will be completely reinitialized
+ on reboot so there may be boot problems on some systems.
+ reboot=force
+ Don't stop other CPUs on reboot. This can make reboot more reliable
+ in some cases.
+Non Executable Mappings
+ noexec=on|off
+ on Enable(default)
+ off Disable
+ nosmp Only use a single CPU
+ maxcpus=NUMBER only use upto NUMBER CPUs
+ cpumask=MASK only use cpus with bits set in mask
+ numa=off Only set up a single NUMA node spanning all memory.
+ numa=noacpi Don't parse the SRAT table for NUMA setup
+ numa=fake=X Fake X nodes and ignore NUMA setup of the actual machine.
+ acpi=off Don't enable ACPI
+ acpi=ht Use ACPI boot table parsing, but don't enable ACPI
+ interpreter
+ acpi=force Force ACPI on (currently not needed)
+ acpi=strict Disable out of spec ACPI workarounds.
+ acpi_sci={edge,level,high,low} Set up ACPI SCI interrupt.
+ acpi=noirq Don't route interrupts
+ pci=off Don't use PCI
+ pci=conf1 Use conf1 access.
+ pci=conf2 Use conf2 access.
+ pci=rom Assign ROMs.
+ pci=assign-busses Assign busses
+ pci=irqmask=MASK Set PCI interrupt mask to MASK
+ pci=lastbus=NUMBER Scan upto NUMBER busses, no matter what the mptable says.
+ pci=noacpi Don't use ACPI to set up PCI interrupt routing.
+ iommu=[size][,noagp][,off][,force][,noforce][,leak][,memaper[=order]][,merge]
+ [,forcesac][,fullflush][,nomerge][,noaperture]
+ size set size of iommu (in bytes)
+ noagp don't initialize the AGP driver and use full aperture.
+ off don't use the IOMMU
+ leak turn on simple iommu leak tracing (only when CONFIG_IOMMU_LEAK is on)
+ memaper[=order] allocate an own aperture over RAM with size 32MB^order.
+ noforce don't force IOMMU usage. Default.
+ force Force IOMMU.
+ merge Do SG merging. Implies force (experimental)
+ nomerge Don't do SG merging.
+ forcesac For SAC mode for masks <40bits (experimental)
+ fullflush Flush IOMMU on each allocation (default)
+ nofullflush Don't use IOMMU fullflush
+ allowed overwrite iommu off workarounds for specific chipsets.
+ soft Use software bounce buffering (default for Intel machines)
+ noaperture Don't touch the aperture for AGP.
+ swiotlb=pages[,force]
+ pages Prereserve that many 128K pages for the software IO bounce buffering.
+ force Force all IO through the software TLB.
+ oops=panic Always panic on oopses. Default is to just kill the process,
+ but there is a small probability of deadlocking the machine.
+ This will also cause panics on machine check exceptions.
+ Useful together with panic=30 to trigger a reboot.
+ kstack=N Print that many words from the kernel stack in oops dumps.
+ noreplacement Don't replace instructions with more appropiate ones
+ for the CPU. This may be useful on asymmetric MP systems
+ where some CPU have less capabilities than the others.