path: root/Documentation/sound/oss/ALS
diff options
Diffstat (limited to 'Documentation/sound/oss/ALS')
1 files changed, 66 insertions, 0 deletions
diff --git a/Documentation/sound/oss/ALS b/Documentation/sound/oss/ALS
new file mode 100644
index 000000000000..d01ffbfd5808
--- /dev/null
+++ b/Documentation/sound/oss/ALS
@@ -0,0 +1,66 @@
+ALS-007/ALS-100/ALS-200 based sound cards
+Support for sound cards based around the Avance Logic
+ALS-007/ALS-100/ALS-200 chip is included. These chips are a single
+chip PnP sound solution which is mostly hardware compatible with the
+Sound Blaster 16 card, with most differences occurring in the use of
+the mixer registers. For this reason the ALS code is integrated
+as part of the Sound Blaster 16 driver (adding only 800 bytes to the
+SB16 driver).
+To use an ALS sound card under Linux, enable the following options as
+modules in the sound configuration section of the kernel config:
+ - 100% Sound Blaster compatibles (SB16/32/64, ESS, Jazz16) support
+ - FM synthesizer (YM3812/OPL-3) support
+ - standalone MPU401 support may be required for some cards; for the
+ ALS-007, when using isapnptools, it is required
+Since the ALS-007/100/200 are PnP cards, ISAPnP support should probably be
+compiled in. If kernel level PnP support is not included, isapnptools will
+be required to configure the card before the sound modules are loaded.
+When using kernel level ISAPnP, the kernel should correctly identify and
+configure all resources required by the card when the "sb" module is
+inserted. Note that the ALS-007 does not have a 16 bit DMA channel and that
+the MPU401 interface on this card uses a different interrupt to the audio
+section. This should all be correctly configured by the kernel; if problems
+with the MPU401 interface surface, try using the standalone MPU401 module,
+passing "0" as the "sb" module's "mpu_io" module parameter to prevent the
+soundblaster driver attempting to register the MPU401 itself. The onboard
+synth device can be accessed using the "opl3" module.
+If isapnptools is used to wake up the sound card (as in 2.2.x), the settings
+of the card's resources should be passed to the kernel modules ("sb", "opl3"
+and "mpu401") using the module parameters. When configuring an ALS-007, be
+sure to specify different IRQs for the audio and MPU401 sections - this card
+requires they be different. For "sb", "io", "irq" and "dma" should be set
+to the same values used to configure the audio section of the card with
+isapnp. "dma16" should be explicitly set to "-1" for an ALS-007 since this
+card does not have a 16 bit dma channel; if not specified the kernel will
+default to using channel 5 anyway which will cause audio not to work.
+"mpu_io" should be set to 0. The "io" parameter of the "opl3" module should
+also agree with the setting used by isapnp. To get the MPU401 interface
+working on an ALS-007 card, the "mpu401" module will be required since this
+card uses separate IRQs for the audio and MPU401 sections and there is no
+parameter available to pass a different IRQ to the "sb" driver (whose
+inbuilt MPU401 driver would otherwise be fine). Insert the mpu401 module
+passing appropriate values using the "io" and "irq" parameters.
+The resulting sound driver will provide the following capabilities:
+ - 8 and 16 bit audio playback
+ - 8 and 16 bit audio recording
+ - Software selection of record source (line in, CD, FM, mic, master)
+ - Record and playback of midi data via the external MPU-401
+ - Playback of midi data using inbuilt FM synthesizer
+ - Control of the ALS-007 mixer via any OSS-compatible mixer programs.
+ Controls available are Master (L&R), Line in (L&R), CD (L&R),
+ DSP/PCM/audio out (L&R), FM (L&R) and Mic in (mono).
+Jonathan Woithe
+30 March 1998
+Modified 2000-02-26 by Dave Forrest, drf5n@virginia.edu to add ALS100/ALS200
+Modified 2000-04-10 by Paul Laufer, pelaufer@csupomona.edu to add ISAPnP info.
+Modified 2000-11-19 by Jonathan Woithe, jwoithe@physics.adelaide.edu.au
+ - updated information for kernel 2.4.x.