path: root/Documentation
diff options
Diffstat (limited to 'Documentation')
3 files changed, 39 insertions, 4 deletions
diff --git a/Documentation/IPMI.txt b/Documentation/IPMI.txt
index 653d5d739d7f..31d1d658827f 100644
--- a/Documentation/IPMI.txt
+++ b/Documentation/IPMI.txt
@@ -505,7 +505,10 @@ at module load time (for a module) with:
The addresses are normal I2C addresses. The adapter is the string
name of the adapter, as shown in /sys/class/i2c-adapter/i2c-<n>/name.
-It is *NOT* i2c-<n> itself.
+It is *NOT* i2c-<n> itself. Also, the comparison is done ignoring
+spaces, so if the name is "This is an I2C chip" you can say
+adapter_name=ThisisanI2cchip. This is because it's hard to pass in
+spaces in kernel parameters.
The debug flags are bit flags for each BMC found, they are:
IPMI messages: 1, driver state: 2, timing: 4, I2C probe: 8
diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
new file mode 100644
index 000000000000..be789685a1c2
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt
@@ -0,0 +1,30 @@
+Abracon ABX80X I2C ultra low power RTC/Alarm chip
+The Abracon ABX80X family consist of the ab0801, ab0803, ab0804, ab0805, ab1801,
+ab1803, ab1804 and ab1805. The ab0805 is the superset of ab080x and the ab1805
+is the superset of ab180x.
+Required properties:
+ - "compatible": should one of:
+ "abracon,abx80x"
+ "abracon,ab0801"
+ "abracon,ab0803"
+ "abracon,ab0804"
+ "abracon,ab0805"
+ "abracon,ab1801"
+ "abracon,ab1803"
+ "abracon,ab1804"
+ "abracon,ab1805"
+ Using "abracon,abx80x" will enable chip autodetection.
+ - "reg": I2C bus address of the device
+Optional properties:
+The abx804 and abx805 have a trickle charger that is able to charge the
+connected battery or supercap. Both the following properties have to be defined
+and valid to enable charging:
+ - "abracon,tc-diode": should be "standard" (0.6V) or "schottky" (0.3V)
+ - "abracon,tc-resistor": should be <0>, <3>, <6> or <11>. 0 disables the output
+ resistor, the other values are in ohm.
diff --git a/Documentation/kasan.txt b/Documentation/kasan.txt
index 092fc10961fe..4692241789b1 100644
--- a/Documentation/kasan.txt
+++ b/Documentation/kasan.txt
@@ -9,7 +9,9 @@ a fast and comprehensive solution for finding use-after-free and out-of-bounds
KASan uses compile-time instrumentation for checking every memory access,
-therefore you will need a certain version of GCC > 4.9.2
+therefore you will need a gcc version of 4.9.2 or later. KASan could detect out
+of bounds accesses to stack or global variables, but only if gcc 5.0 or later was
+used to built the kernel.
Currently KASan is supported only for x86_64 architecture and requires that the
kernel be built with the SLUB allocator.
@@ -23,8 +25,8 @@ To enable KASAN configure kernel with:
and choose between CONFIG_KASAN_OUTLINE and CONFIG_KASAN_INLINE. Outline/inline
is compiler instrumentation types. The former produces smaller binary the
-latter is 1.1 - 2 times faster. Inline instrumentation requires GCC 5.0 or
+latter is 1.1 - 2 times faster. Inline instrumentation requires a gcc version
+of 5.0 or later.
Currently KASAN works only with the SLUB memory allocator.
For better bug detection and nicer report, enable CONFIG_STACKTRACE and put